Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Hello,
I have consulted the nRF52840 Dongle and cannot get the spec of the PCB antenna.
I need the information for FCC Test. Could someone help me?
Thank you very...
I found lines 766 - 768
CONFIG_GPS_SIM_DEV_NAME="GPS_SIM" CONFIG_GPS_SIM_BASE_LATITUDE=6325280 CONFIG_GPS_SIM_BASE_LONGITUDE=1026201
in \ncs\nrf\samples\nrf9160\asset_tracker...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
Things were working ok yesterday but today I can't open any projects. For some reason now, it fails and says the project file is invalid. Here is the output
Loading solution...
Hi,
My system needs to maintain certain gpio at their state at all times, including when switching to bootloader,
I understand that reset will also return my gpios to...
I'm trying to set up an ESB PRX on an nRF52 that has to communicate with an nRF24L01 chip acting as PTX. Because I want to react to the received data as quickly as possible...
Hello,
I am trying to use Softdevice and the latest Github version of 802.15.4 support. The make (using linux/armgcc) fails on
nrf_raal_softdevice.c
because nrf_802154_radio_irq_handler...
Using SDK 15.2 on an nRF52832 using SoftDevice S132. FDS works OK unless the SoftDevice is enabled. None of the examples work. We've tried the peripheral example, GitHub examples...
Hi,
I'am testing direct advertise and I found strange behaviour with "nrf connect" app.
1. Direct advertises won't be proceeded on "nrf connect" unless there is at least...
Hello everyone
I got back on my bluetooth mesh project after an interruption and at the time I remember having the same compilation problems solved so far.
I worked with...
Hi all,
I acquired the wonderful nRF9160 DevKit which embeds the ARM CryptoCell 310.
Rather than using the mbedTLS or TinyCrypt libs, I would like to rely on the CC310...
hi....
i am just started to program the mesh , i am getting the error in my example code , how to solve ? this is the latest version of 3.1
boards.h: No such file or ...
Hi,
I am using 15.2.0 SDK and 3.0.0 Mesh SDK for developing the nRF Mesh.
I am using segger IDE for programming but I am looking for a way to program the device with hex...
Hi
In MESH 3.10 SDK，i want to configure and use virtual address, but i can't add the virtual address in both pulication address/subscription address when i use NRF Mesh...
Hi Sir,
Normally, the printf() may show the message to UART_0, is there any way we can re-direct the message of printf() to UART_1?
in other words, can we choose the...
