Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am attempting to use Enhanced Shockburst/Gazell working with coded PHY, in order to achieve long range communications with very lower power consumption. I have searched...
Hello, I am experimenting with your nrf5SDKforMeshv310
I can compile and download the included examples.
Because I own a few Thingy 52, I wish to flash them as light_dimming_servers...
hi,
I am trying to add SPI (master) codes into the ble_app_uart.
My setting for SPI is as follows:
#define SPI1_ENABLED 1 // #define SPI_INSTANCE 1 /**< SPI instance...
Hi I am using nRF52832 board amd i am trying to debug ble_app_uart as Central.
BLE connection is established between this central application and the peripheral.
Opened...
i am using nrf24l01+ on arduino devices, one arduino device as master, and other arduino devices as slaves. I like master to broadcast a radio (dataToSend) toward all slaves...
nrf52832, keil with startups from sdk13
Initialization:
IntHandler:
With one event everything working well. Then I add another:
I need to measure SENT signal...
hi.... folks
i am using nrf52840 development kit , and i debugged the merged programs such as uart and twi program in it .does it will give the temperature data?
i am...
Hi all,
Please refer to the SDK version : nRF5_SDK_15.2.0_9412b96.
We need to use two uarts simultaneously for module & device respectively.
For example :
UARTE0 ...
We, I am using nRF 5 SDK v 14.2.0.
Power-off has occurred during program development. I can not identify the location, Functions that are not memory leak, buffer overflow...
Hi,
Now, I am using the nRF52840 to develop and do signal test. Can you share me some tool that can make the board enter the test mode?
Best regards
Simon
Hi:
PREJECT: nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hrs_freertos\pca10040\s132\arm5_no_packs
When TWI0 and GPIOTE are turned on at the same time, the...
I'm trying to get the AT commands sent in the asset_tracker example written out together with the other printk statements. I have tried adding this to the prj.conf: CONFIG_LOG...
I used the nrf52840 as the central device, use SDK15.0, scan then connect the peripheral toys.
sometimes i found the central can scanned some ble peripheral but can't connected...
Is there a way to have 6 different GPIOs act in unison off one event/action? I need all 6 to go ON and OFF at EXACTLY the same time based of an event or action.
