Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Dear Nordic DevZone,
I am having a problem using SEGGER Embedded Studio for ARM
Release 4.12 Build 2018112601.37855 Windows x64
When I select a Group under Registers...
I have ported the NFC URI example to a custom project that I am working on (platform details listed below). I am using an Android phone running NXP tag info app to read the...
Hello
I have a question to ask, I want to beacon the battery level and temperature. I know there is a temperature sensor inside, if I want to use saadc to get the sensor...
Hi All,
I compiled Keil UART application and it is working fine on Eval Board. But the same code I started running on customized board and here am getting only 1 byte every...
Hi there,
I am adding schedule to my application calling app_sched_event_put() inside a context interruption from Button to enable a sequential write to a memory using SPI...
Hi,
I’m trying to use the SAADC on nrf52832. I’m not using softdevice (I’m not doing BLE code) but it’s present on the chip (to use it for DFU). When I program the chip...
Hi I am using the nrf51422_XXAC device. I want to make a connection with my app alone. other apps should not be able to connect. please help me with sample code. I am new...
Hello,
I'm having issues trying to connect to a third-party peripheral (called iTag from now on).
I have an NRF52832-based device running as a central. My device is running...
Hello Nordic Devzone,
I have a few queries regarding using VID& PID for a hardware.
Is there any cost involved when using the Nordic VID & PID?
Will Nordic provide a...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
Hello.
I have a nRF9160DK.
I want to try this uart example: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/uart
I want to config the...
Hi everyone,
I want to transmit a HEX array I read from a peripheral using SPI communication (I initialize my RX_BUF in the SPI_EVT_HANDLER() function) via BLE. I am using...
Hello All,
I am working on nRF52810 custom board. I used segger studio in windows 7. For reference i used nRF52 SDK 15.2.0.In my application i used i2c peripheral.
My...
Hello,
as I understand the accuracy of the LF Crystal oscillator for the nRF52832 development board DK_PCA10040 ist set within the sdk_config.h in the following way:
...
Using NRF52832 on a custom PCB with 32kHz + 32MHz crystals, very close to the reference schematic
Using NRF52 15.2.0, S132, arm5_no_packs, Kiel uVision 5.23.0.0
The example...
