I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
We have an application where certain executions hold more priority over BLE link. We are implementing a critical section(disable/enable interrupts). However, in some corner...
Hello I've noted some problems when try to use the app_timer in repeat mode with a tick time <= 100ms. I see that the BLE Mesh SDK sets the RTC1.CC[0] compare register in...
I my application, I wish to send a large (60 bytes) bulk of data atomically, i.e. either send all or nothing. Assume I cannot increase the MTU.
Is it possible to query...
Hi
I am using the SDK 15.2.0 and developing for a NRF52832 using Segger.
I have a problem with the define NRF_SAADC_CHANNEL_COUNT in "nrf_saadc.h". It is set to 8. ...
Based on Mesh SDK 2.1.1.
I use light switch proxy client & proxy server to test server publish function.
But when I use the phone setting network, I found that the client...
Dear nordic,
we build a custom board with nrf52840. Now i face some issue i can't flash the board. when i start flashing its show some warning reset pin is high.
I...
Hi,
I just want to verify-
The MAC address of the bootloader is the app MAC address +1, assuming we are using the default configuration.
Is that correct?
Thanks, ...
Hi Support team,
The Online Power Profiler is calculating the Average Current consumption for nRF52840 DK board in a wrong way.
Calculation is of blocks. => Pre-processing...
Hello
I would like to integrate DFU into my application
but, when including:
#ifdef BLE_DFU_APP_SUPPORT #include "ble_dfu.h" #include "dfu_app_handler.h" #endif...
Dear NRF Team:
I successfully updated the firmware (blinky_nrf52840_xxAA_s140_6.1.0) according to the Mesh DFU steps.
However, the second DFU cannot be performed after...
I am experiencing an issue where the program hangs on one board, but not another. I am able to program the Evaluation board (EV BT832AF) ok and run everything, but when I...
Hello,
I was wondering if it is possible to change some of the BLE Stack Configurations based on the number of devices connected...
e.g. Changing Connection Interval and...
Hi,
I am evaluating the Firmware on this github repo and my nrf52832.
At the moment I am compiling it using my makefile, however I would like to import this project...
Hi All.
We have flashed the hex-file of ble_app_blinky for pca10040 on the debugger, and things work fine.
We are using sdk-15.2 with softdevice-6.1.1
So, a question...
Hi there, I am having issues knowing how to get access to data coming through a VisualGDB embedded (C) project using the pc-ble-driver. I have my project working fine and...
