Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I have an application where in i need to scan for non connectable advertisements as well as advertise beacons on the device. I am using the Fanstel BT832A module which contains...
Hello,
i would like to interface nrf51822 with an rfid reader mfrc522 using SPI.So, i went through the example of spi_master in SDK 8.1.0.How can we access the value of a...
Hello all,
I am right now working on one project. where i use nrf52832 BLE board. right i am doing i2c communication of temperature sensor(lm6bd) with ble board. but can...
Hello All,
I am using nRF52810 programming in segger embedded studio in windows 7. i am trying to do i2c communication between sensor and nRF52810.i am create custom service...
Hi,
I have a question about direct advertisment - if I direct advertise to one android, then other devices won't show it am I right? How does this direct advertising works...
Hello all,
I am using nRF52810 programming in segger embedded studio in windows 7. I am refer SDK nRF5 v5.2.0. I am trying to do i2c communication between sensor and nRF52810...
I had a couple of questions regarding the SPI slave peripheral on NRF52:
What is the behavior of the peripheral if a transaction completes (NSS goes high) and another...
I used the example code of MQTT pub and sub with nRF52 DK which has nRF52832 in it. I have sent the data from one kit to another with the help of Raspberry pi 3 as a router...
Hello. I need a bit of help with my case. I have nRF52832 dev kit. I have set heap size to zero in Makefile:
And even with that change I am still able to allocate memory...
Hello,
I have some questions about NFC on nRF52832:
1.Could NFC on 52832 works as a card reader , for the mifare 1 card, or named S50 card?
2.In the example "nRF5_SDK_15...
Hi all,
I have read that ANTUSB-m is needed for ANTWARE running in Windows PC. Can I use nRF52840 DK or nF52840 USB dongle in place of ANTUSB-m? If yes, where I can find...
Hi all
I have a custom Board, I have tested it a lot. NRF51822, programed with Mbed..
In general the Software and Board WORKS FINE, but I found some problem in my procedure...
Hello
I am following example on :
examples/dfu/secure_dfu_test_images/ble/nrf52832
when flashing:
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hello,
I'm trying to use this code https://github.com/kimyd/SHT1X_on_nrf51822 to communicate with an SHT11 sensor via GPIO pins. I have a Saleae hooked up an can see the...
Our project uses nRF51822 with SDK12.3.0 and s130. We are using app_timer_appsh.h and app_scheduler.h to make a "UTC timer" by counting a static variable each 1S timeout ...
