Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I'm trying to update the modem firmware on my new nRF9160 DK using nrf9160_mdm_dfu --update , but I get the following error: pynrfjprog.API.APIError: An error was reported...
Hi all. I am trying to work out if the following is possible;
At the moment I have setup a freq counter (analog signal) on the nRF52832. It uses the comp to detect up crossing...
Hello everyone, I'm using the nrf9160-DK and I'm trying to read data from an external sensor over UART and I'm a bit lost. I would appreciate if someone could point me in...
I'm in the process off trying to learn the world of BLE. Currently, I'm using nRF Connect for Desktop (w/USB dongle) as the learning platform. Using 'Server Setup' I configure...
We use the chip product of nRF52810 to do a wireless module design. While in sleep mode, we found some spikes, which are 0.6mV in amplitude and 180ms in period. It is not...
Hi,
we use CC310 (in nRF52840) in a project (working directly with the CRYS API from SDK 15.2.0). When doing a test of ECDSA with secp256r1, following the one given within...
Hello,
I am trying to change the tx power for my nRF52-DK which is having nRF52832 chip. I trying the following code to change the tx power to -40 dB.
int8_t tx_power_level...
Is there any example about the dongle nrf52840 act as a central? Is that possible? In that case for a ble connection between dongle and board a service does to be create on...
Hello,
I need to long WRITE AND long READ from a central/client (android) to a peripheral server (nrf52). when I says long it means longer than the MTU.
LONG READ
I...
At the top of the Nordic home page, there's a link for "Bluetooth Software":
Following that takes us to https://www.nordicsemi.com/Software-and-Tools/Software/Bluetooth...
Hi!
In a Bluetooth mesh, we would like to get a feedback message from a group of nodes, via a reply message, after sending a message to the group.
The Bluetooth blog writes...
Hi. I am trying to get the peer address from of the peripheral my central has connected to within the BLE_GAP_EVT_CONNECTED event.
The following returns the address, however...
Hi folks,
I try to do create timer. Therefore i want to adding some files in blinky project. So here is some screen shot. Thats about debug error. First i used SDK 15...
Hi team,
I was asked by one of my customers, that if they can use nRF51822-QFAC (existing products design) as peripheral while connected by 2 central (Phone & Router)...
Hi I am a fleding embedded system engineer trying new ways to develop a process( Flashing) in my company,
My company's senior software has designed a control box which...
