Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I want to add simple on off switch model via SDK 2.2.0.
I'm already add client model to project,when provisioner add client node,Provisioner RTT jump error opcode status...
Hello Everyone,
Maybe this is a very silly question.
I am trying to implement timer in nrf51822 with S130, SDK11.
Code snippet:
void TIMER1_IRQHandler(void)
...
Hi,
i Have two development kits where one acts as uart central and another acts as uart peripheral .
In that i have given the peripherals different names( DEVICE_NAME...
Hi, I would like to ask how can i get the current consumption that was stated in the datasheet which is 0.7uA and the value I get from the reading is about 8-9 uA.
Is...
Hi team,
I am using sdk 14.2 ,nrf52840 DK board.
I am getting the following error while running nrf5-mpu-ble-simple code in keil. <error> app: Error 0x000D (13) at line...
hi.....
i am using nrf52832 ........
i want to wake up my device from sleep mode ... i have used the command for sleep mode sd_app_evt_wait() ...... i dono what command...
Hi Sir,
We plan to use the serial DFU to upgrade the 52832 (Host MCU + 52832), we use UART as the communicate interface.
Do we have the example code for reference for...
Hi,
I'm experiencing frequent crashes in the softdevice on an nrf52832, running SD version 6.0.0 with SDK 15.0. The crash seems to occur when interfacing to the device over...
So I can live with the 60uA power draw I get shortly after a power cycle but the strangest thing happens. Over a short period of time the power consumption ramps up to, well...
Hardware: customized board based on PCA10056
SW: nRF5_SDK_15.2.0_9412b96
Change:
Merge ble_app_blinky example into blinky_rtc_freertos.
/cfs-file/__key/support-attachments...
NRF52832
SDK 15.2
Two MCUs communicate through serial port. If the other MCU is not powered on, nrf52832 will not run (LOG error > app: Fatal error). If UART is not initialized...
Hi everyone,
These days, I am thinking about how to make some upgrade about the sound module of thingy52.
It would be quite funny to make some other sound samples rather...
I want to know the project which code was developed with IAR,the project can port to keil MDK? If I could,where do I need to change,and how to do it .thanks
I use SDK15...
