Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi !
I wrote a "central" device which works with multiple pheripherals.
Each pheripheral (Other NRF devices and also IOS) is going throw BLE_GAP_EVT_CONNECTED and when...
I am using pyserial on OSX as well as Ubuntu to send commands to the serial CLI via the JLink virtual com port for testing, and am occasionally experiencing lost/mutated characters...
Hi everyone. I am a beginner i really need help regarding an issue. I have two nrf52832 modules, on each of them i have a sensor from which i read some values. All i want...
While testing and debugging our current state of development, sometimes our devices go totally offline (thread visible via mqtt-sn last will, no ble advertising).
I found...
Hi,
Just to share my though here.
I think it is better way to decouple the BLE and application with dual core design.
It help to get rid of application latency due to...
Hello Everyone,
We have 2 devices. 1st device is flashed with the Eddystone example & sending TLM info. The 2nd device is flashed with a modified version of the ble_app_hrs_c...
Hi.
So I'm trying to configure my SW to use two uarts (as I've understood that uarte and uart are separate modules that can be used at the same time).
As the app_uart...
Dear nordic,
I implemented a uart in BLE application its works fine.
I need to reduce current for that i enable and disable uart but when i call function disabled or enabled...
hi team,
real quick; The accuracy internal reference (0.6V) used in the SAADC is specified in COMP section of the data manual as +/-3%. The gain error in the SAADC is...
Hi,
I was just trying to build the light_switch_provisioner_nrf52840 code using Segger Embedded Studio. However, I've got a error build/light_switch_provisioner_nrf52840_xxAA_s140_6...
What is the function of db_discovery_init (); , I am migrating a code from SDK 8 to SDK 14.2 and I can not find that function, I do not know what library it contains or how...
Hi Nordic.
I am currently working on nRF52810 chip and the main power source is lipo battery. The battery is charged via USB could you recommend an efficient power management...
Hi,
I am currently migrating my controller from nRF51 to nRF52832 . I am facing an issue where in when I try to do an TWI communication with MPU9250 on nRF52 the code gets...
Hey
all process of burning work great without use of reset pin.
question is do we need to change it and wire pin to jtag connector?
what is the added value of the pin...
