Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello
I have an problem using I2C on my custom board which uses an Nrf51422 SOC.
I have an RTC chip connected to it and I have no idea how to use your libraries.
The...
Hi! I'm using Arduino BLE micro and good results so far. With some accellerometers connected via I2C.
Today I have a strage behaviour.
I connect the arduino, ok, open...
Hello everyone,
I have a nRF51822 dev board connected through USB to my PC.
I have connected it to COM5 using Terminal and now I would like to interrogate BLE like we...
Hi guys
I have a custom board with NRF51422QFAA, load "s310_nrf51422_2.0.1_softdevice", program on "nRF51_SDK_7.2.0"
the bootloader I used is "dual_bank_ble_s310"
...
Is there a way to control the max # of packets be transmitted in one connection interval?
(We want to vary it from 1 - 6, knowing that nordic can support up to 6-7.)
Has anyone had any success setting the configuration register on TMP102/112 temperature sensors via I2C? I'd like to switch the sensor to one-shot mode to further minimise...
Hi everyone !
I'm trying to send data from an nrf51822 to an nrf24l01 with arduino and I guess I'm doing something wrong...
For the moment I succeeded to have these talking...
I have a simple ANT beacon application.
UART will be enabled to do some communication. How can I turn it off before ANT goes into sleep mode? Is there a call back function...
I want to send a set of 64 bytes data with ble. as I understand, the max data length I can send within a characteristic is 29 byes. when I send 4 bytes data it works fine...
Is it possible to bit bang a 9600 baud UART on the nRF51822 while the BLE softdevice is running?
The reciprocal of 9600 baud is around 100 µs, so the interrupt handler...
Hi Team,
My application is based on nrf51822 SoC in which I am using
BLE and UART interfaces.
There is single UART available and I have used it in communicating with...
Hello,
I am using am using sd_ble_evt_get and sd_app_evt_wait in an endless loop for handling all incoming events.
If I block this loop from executing, I'd expect that...
Hi all
I'm struggling with the easyDMA UART of nrf52. I've got a preview nrf52-DK here where I wanted to make a simple example with the following code but I never reach...
