I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello Nordic Team,
I am working on integrating the nRF21540 RF Front-End Module (FEM) with the nRF52840-QFAA in the 48-QFN package. Could you please provide the following...
Hi, I have reviewed the light_bulb app code in NCS2.8.0(include src code/CMakeLists.txt/prj.conf and so on)。 But I can't find where the path of matter is included, could you...
Hi all,
I wanted to enable read/write protection for MCUBOOT partition in my firmware from the application and encountered a strange problem. The build (build system - default...
Hi there,
This almost certainly has a simple answer but I can't work it out. I'm using the sample WIFI Scan for the above boards and can successfully scan away. But I'd...
Hi there, I am new to working with UART. I have managed to load the Nordic UART Service Client(Central) and UART Serial Port Emulation(Peripheral) without any sensors attached...
So, I am working on nrf52840 with nrf connect sdk and I want to get date and time in my project, I found a library in nrf connect sdk ->libraries->other libraries->date-time...
NCS 2.7.0 Zephyr 3.6.99
I have &uart1 described with status = "okay"
With a sub node of gnssdev: gnss-nmea-generic also with status = "okay"
I have tried with both pointing...
Hi, In one of the previous ticket (link: ), there is a link about an example to create an application with USB CDC/ACM and MSC at the same time. The link is no longer valid...
I am writing software for a battery-powered device that needs to go into the lowest power possible sleep mode when not in use and be able to wake up with one of 8 buttons...
Hello,
I've been trying to get the nRF Desktop Dongle/HID Forwarder to work, ie. I program a nrf52840DK as a HID forwarder, it connects to my bluetooth keyboard, and then...
Hey Team,
While connecting the battery to the nRF5340 Audio DK, we have observed that it only charges the batteries with 3 pin connector is being charged. However when we...
Hi, I just want to read accel and gyro data from the on-board BMI270 IMU on the Thingy 53. I'm using the sample code from zephyr and I've modified the dts and overlay file...
my chip is nrf52833. In guide document , the XC1 and XC2 would connect to capacity. Both pin is used.
My project need one pin TCXO. which pin I should connect to? XC1 or...
Hi, everyone.
I am testing reading/writing data between n52840 and n9160 through UART with buf_len=1(byte by byte) based on Zephyr's UART_ASYNC_API provided in ncs v2.6...
