Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I’m currently developing an application for the nRF52833 that collects sensor data via SPI and sends it out over BLE using notifications. My primary goal is to achieve...
Hi,
I am trying to create a device two temperature measurements.
I have created two endpoints like this:
but when I try and compile, I get this error:
G:/ncs/v2...
Hello! I am trying to monitor mbedtls heap usage in the azure_iot_hub sample (v2.8.0), building for nrf7002dk/nrf5340/cpuapp/ns. I can see in modules/crypto/mbedtls/library...
I am trying to enable userspace for my project. I am getting this error on one of the last steps related to some debug info.
I can compile fine with all the same configs...
"I added an endpoint called Matter Extended Color Light to the matter_bulb example. After compiling and flashing the firmware, HomeKit only recognizes and creates two dimmable...
Hi,
I want to connect LDC2114 to nRF9160. I write the nrf9160dk_nrf9160_ns.overlay and the astri,ldc2114.yaml. I don't know how to set GPIOs in & i2c1 - ldc2114: ldc2114...
Hi all,
I am dealing with a similar problem to this post: https://devzone.nordicsemi.com/f/nordic-q-a/110715/creating-development-env-for-nzrzf5340-error-warning-nrfjprog...
Hello,
I am using the nRF54L15-DK and nRF Connect SDK v2.8.0, and when I try to compile the Zigbee Coordinator sample, I get an error saying that <zboss_api.h> cannot be...
I'm using NCS version 2.6.1 with a NRF9161DK
Recreating the issue:
Follow the instructions in the readme of the sample: Cellular: nRF Cloud multi-service
Build with...
Hi nRF experts.
We are RF module manufacturer, We are developing nRF54L15d module, When we develop production test software, we need to test power off current, Using the...
I'm trying to get a gas gauge and charger IC to work on the i2c bus. Both have different addresses. I'm able to read from the gas gauge address but not the IC. Are there specific...
Hi Nordic:
I use NRF54L15 for my product and hope to use ANT+AND BLE. Does NCS2.8 currently support it?
I couldn't find a example program for ANT+in NCS2.8. How can I...
Hello support team,
I am developing a mobile app to communicate on BLE coded phy (long range) with nrf5340DK. The nrf connect for mobile on android works fine, but not ios...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
