Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I've been having issues trying to add MCUBoot to our application. The app is based on the Common Application Framework (CAF) with a structure based on the nrf_desktop...
hi,
sdk 17.1.0
Can I call " NRF_LOG_INFO" API back to back ? Does it copy the contents of the buffer (var) to an internal buffer ?
For example, in the below code, does...
Hi,
I am using nrf52833 ic with zephyr for firmware development my product is a battery based device and i want to reduce it power consumption when in ideal state what are...
Hello all,
I have pinged the sensor on the "twi bus" successfully, now I am following the post on the read/write function that is needed to actually read the data off the...
Dear nordic engineers:
The only example I can find about flash is under zephyr/samples/drivers/spi_flash. However, the flash writing is pretty slow, and the MCU is halting...
I'm trying to record audio from Nano 33 BLE Sense which is using an nrf52840 microcontroller. But the default PDM library available doesn't allow me to record at a higher...
HI
I would like to check if it is possible to setup 3 sets of nRF5340 Audio DK as a master with two slaves.
Where the master and salves are able to send audio (via mic...
Hi All,
I would like to know how Nordic's pairing mode corresponds to the bluetooth specification.
If my smartphone(initiator) is keyboard display,and my slave(responder...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I would like to update SoftDevice from v7.0.1 to v7.3.0. Are there any areas...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
I have trouble with DFU. I could implement SMP server into my project according to your guide. (+) Add DFU support to your...
Uns NCS v1.9.1 and VSC, I am attempting to run through the Device Firmware Update (DFU) with MCUBoot bootloader exercise.
I am running to a road black in figuring out how...
I have a Bluetooth device that has a long characteristic. On previous central device projects there is usually a function like read_long_char. I am trying to get a zephyr...
We've built a device with the nRF5 17.1.0 SDK on nRF52832 which operates as a HID keyboard. On iOS and Android this is working fine, and it's working fine sometimes on Windows...
Hello, trying to get v1.9.1 lte_ble_gateway working on Thingy 91. Using Thingy 2020:23 1.4.0, which works all good with zip thingy91_fw_2022-02-17_ec486dab (tracker, nrf cloud...
