Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I have a combined asset_tracker_v2 and central_main. I can connect perfectly and receive data from a single BLE advertiser. I need to be able to connect to 1-4 simultaneous...
Hi,
I’m using an nRF5340DK with nRF Connect SDK 2.9.1 , configured as both Central and Peripheral with the nordic SDC running the network processor Goal: allow the board...
The firmware always halts execution during boot after providing these logs:
26/05/22 10:38:33.925 89737.861 13892 0 E: Device id 00 00 00 does not match config 1f 16 01...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
I’m working on a custom board based on the nRF9160 (SICA variant) and trying to enable MCUboot + TF-M with sysbuild. I’m running into an issue where the system never reaches...
I’m using the RADIO peripheral for BLE 1M connection-event RX→TX turnaround.
Current flow:
1. RADIO receives a data PDU. 2. RADIO reaches END/PHYEND and disables. 3. In...
Hello Nordic Support,
I am using nRF54L15 with NCS v3.2.3 .
The device is using Legacy Connectable Advertising with Flags and Complete Local Name in the advertising data...
Hello,
I have a few questions about the nRF9151 DECT NR+ modem.
I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hello guys,
Im developing RTLS with DWM3001C and right now Im working on personal tag powered by CR2450. So naturally, power consumption should be as low as possible....
Hello.
Are you able to give any specific details around an SDC Assertion with File ID 13 and Line 451 please?
The nRF Connect version is v3.2.4.
I'm trying to isolate...
Hello,
I am currently optimizing the power consumption of an nRF54L10-based project.
While I know that system-off mode is the most efficient, my current implementation...
Hi,
Customer using nPM1300 would like to know what are the minimum and maximum values of Rshphld? These values are not in the datasheet.
Best Regards,
Nic
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
