Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi there, We have a product using an nRF52832-QFAA, with the SDK15.2.0, the 132 Softdevice, and an application based around the Nordic UART service (nus). Customers are reporting...
Hi everyone,
i'm writing to ask some advice for my NBIOT AWS application with the nRF9160 DK.
I'm currently using the aws_iot sample available as a baseline for my project...
Hi everyone,
I am working on a project, in which I have n nodes that communicate with each other (peer to peer communication). In addition, each node is able to communicate...
I see mainline Zephyr is now on v3.0.0 since end of Feb. I assume the bump from 2.7.x to 3.x means substantial changes. When will NCS move to a 3.x zephyr?
I ask this...
Hello.
It is being developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
Previously, I inquired about how to add a value to the characteristic with...
Hi,
Our customer needs CAT-M, CAT-NB, GPS RF test data
I see that devZone has less information about CAT-M, CAT-NB and GPS RF performance tests
1. Please provide GPS...
As requested I am posting a public question based on Nordic's request here:
https://www.linkedin.com/feed/update/urn%3Ali%3Aactivity%3A6911310498537869312/?commentUrn=urn...
Hi,
parameters A NRF_SDH_CLOCK_LF_RC_CTIV
parameters B NRF_SDH_CLOCK_LF_RC_TEMP_CTIV
1. The internal RC parameter should be configured as follows, but how are parameters...
If AT+CFUN=1 will not get modem connected/registered to a network, what retry algorithm does the nRF9160 implement? Is it something like exponential back-off algorithm?
I'm attempting to add NVS functionality to my code. Had a play around with the zephyr/samples/subsys/nvs example. It was working originally, and then when I started porting...
Hi!
For a project I need to sample an I2C sensor for a period of 1 min with 1 sec between samples with a nordic nrf52832. During this 1 min, a co-processor communicates...
I'm trying to build a custom board in VS Code to use with the nRF9160. I'm using a Thingy91, so I took the board file for that, and copied it into the project directory. ...
I need to test the SPI communication in my nRF9160DK. I had tried to run the spi_loopback but failed to create a project in segger studio. Are there any SPI tests available...
So I have taken a starting point of adding multiple characteristics in the same service using this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth...
