Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all,
I was looking at all ble events and found a few GAP events related to security:
BLE_GAP_EVT_SEC_PARAMS_REQUEST
BLE_GAP_EVT_SEC_INFO_REQUEST
BLE_GAP_EVT_PASSKEY_DISPLAY...
Hi,
I've been monitoring the posts regarding ARM support for the various Nordic tools and libraries - and its been almost two years now since the M1 were released, and still...
I know this should be possible if the phone acts as a BLE advertiser.
But is there any way to scan for a (specific) phone MAC address, if the phone is not advertising BLE...
Hi,
I am writing the code in the cpp for bt_le_adv_start () function with BT_LE_ADV_CONN as input parameter, this helper macro is not compiling in cpp. It is throwing the...
Hello, guys!
My goal is to monitor battery voltage by using a voltage divider and ADC peripheral of nRF51822 SoC. I find that this example perfectly fits my needs. Consequently...
Hey, I found some plot difference when using write and transceive functions with nrfx library (zephyr os).
I'm trying to send 0x11 using this two codes:
And here...
Hi,
I have been mingling with kernel funtionnalities of Zephyr. I am trying to improve my application using an event based approch and threading.
I am trying to define...
We use nRF9160 on our own board with SDK 1.9.1. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We are connecting to an MQTT broker...
Hi everyone,
i'm currently developing on nRF9160DK with AWS brocker via NB-IOT connection and i don't know if i'm encountering an issue.
Until now, every time that i reboot...
sdk nRF5_SDK_17.0.2_d674dde
I used some flash to store data.
But before dfu,it was equal to (FF FF FF FF FF FF FF FF|........) and after dfu,it was equal to (29 48 0C...
Hi,
In a multi-role central-peripheral code for a nRF52840-DK based device, I have to send a buffer acting as a peripheral. I use the ble_nus_data_send function sent as...
Hi all,
I am currently trying to realize a USB to Uart bridge with the nRF52840 development kit.
I used an old sample as a starting point for this task namely the " usb...
Hi,
I need a sample project for upgradable mcuboot, I am to understand that to have mcuboot upgradable, I need to have 2 stage boot loader, wherein 1st stage bootloader...
It's mentioned in this forum that MQTT-SN may be implemented on nRF connect SDK. I would kindly ask if there is anything available about that? And will MQTT-SN be officially...
