Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi everyone,
I am working on interfacing the nRF52840DK with a 24-bit mems microphone INMP441 through the I2S peripheral. As multi-sources pointed out that the nRF52840...
I'm using macOS 12.3 and Python 3.9.10 from brew. When I "pip install nrfutil" I get nrfutil-5.2.0. Trying to run that results in "NameError: name 'xrange' is not defined...
After installing software, on Linux environment, and run power profiler, all seems to work fine, but after select PPK2, (D4f942375182 device) appears on top selected, but...
Hi,
We tried to remove a component that was glued to the top of the nRF9160 SiP and accidentally removed a bit of the SiP's metallic covering (see pic attached). Our guess...
Hi Team
We are using the Nrf52840 module for our dev purpose. As part of image update, we Erasing and load the new image to the chip by using Nrf connect App with Jlink...
Hi,
We have been designing a more robust version of the SLM application and in our testing we noticed a problem that we couldn't work around.
If the modem library's RX...
Hi -
I can't seem to find the answer to this question in the docs, or in the forums. What I'd like to know is - what happens if I update the bootloader and its size increases...
Using nRF5 SDK v16.0.0 on nRF5232. IDE = SES
When advertising is started, I want to advertise initially for 30 seconds, so I set APP_ADV_DURATION to 3000, and the device...
I'm working on an nrf52840 dk. I need to print the sensor data on the command line. I've added the sensor config to the prj.conf file as well as the sensor and sensor_shell...
Hello, Support
I am looking for AT Command example running on nRF52833, host interface is UART interface , and the SoC will be running like a AT Client?
Could anyone help...
I tried to work the zephyr MPU6050 out of the box but it returns "failed to find sensor MPU6050". I can't seem to find a solution to this. The overlay and prj.conf file were...
Hi!
I am working with an nRF5340.
- Is it possible to somehow fill an array with values read from a GPIO OUT register using DMA or PPI?
- Is it possible to assign...
i have installed segger ide and nrf connect for desktop for programm nrf9160 , i have successfully uploaded Blinky code (zephyr) .but now i want to create a new project ....
By default, CONFIG_ZBOSS_OSIF_LOG_LEVEL_CHOICE was set to ZBOSS_OSIF_LOG_LEVEL_INF. But I'd like to increase the log level to debug a problem I'm seeing. When I increase verbosity...
