I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi DevZone,
1. Description:
I am going to use the nRF9160 SiP in a project on a custom PCB which will house the (LN60G840F, which has an nRF9160 on it). The application...
Hi support team,
I have a nrf 51822 beacon black version and developing with nRF5SDK1230. i'm learning about update firmware for it over BLE. i try to run example dfu/bootloader_sercure...
Hello,
I'm using an nrf52dk board and I am trying to get the RSSI value, and it works fine with the nrfconnect app, except that the the transfer doesn't start at the first...
Hello guys,
I want to work with NRF Mesh but I need help with answering some general questions:
1. Is the current version of the SDK ("nrf5_SDK_for_Mesh_v5.0.0_src") power...
HI,
In my custom board of nRF52805 , I am able to program basic UART application. chip is also generating internal voltages on DEC1 & DEC2 lines.
But i am not able to...
Hi,
I would like to include the direct test mode in my default application that runs the BLE stack. Is this possible ? Ideally I am implementing a custom NUS like service...
Hello,
I wish to download my source code to nRF5340 DK board.
I am working on Ubuntu, SEGGER Embedded Studio for ARM Release 5.50d, ncs 1.6.99 version.
After compile...
I'm trying to restrict the policy used to ensure that the AWS FOTA sample is working. The "allow everything" policy that is stated that it can be used for test purposes seems...
SoftDevice: s140_nrf52_7.2.0_softdevice SDK: nRF5_SDK_17.0.2_d674dde Problem: We trying to use the Secure DFU buttonless feature on our custom board. Our custom board has...
Hello,
We are currently using softdevice version 7.0.1 and SDK version 16.0.0. We are having difficulty nailing down a rare hard faulting bug. Very rarely, the device will...
Hi, I'm using Segger Embedded Studio for developing farmware of nRF52840.
and, using
nrf5_SDK_for_Mesh_v4.2.0_src
nRF5_SDK_16.0.0_98a08e2
I would like to use "es_battery_voltage...
i wish to change P0.13 as tx, P0.15 as rx , P0.17 as ctx , P0.20 as rtx
I change in bsp definitions and it worked for uart peripheral example,
I also change pin...
Hello,
The USB connector came apart from the nRF9160 development kit soon after a purchase was made from Symmetry Electronics. Would it be possible to have the board replaced...
