I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
nRF5 SDK can enable radio notifications by few API calls for example: https://devzone.nordicsemi.com/f/nordic-q-a/3481/radio-notification-only-after-ble-radio
with NCS,...
Hi,
I use the example Android Application from Bluetooth to send a generic onoff message from the phone to the proxy node which is also a light switch client ( https://www...
Hi,
My app, based on SDK17.0.2 and SD S340 ues both ANT+ and BLE. While connected to the app runing on the NRF52 from my phone app through BLE, my app on NRF52 sometimes...
Hi Team,
We are designing the Nb-IoT Pet Tracker with nRF9160 SOC and We are performing the NB-IoT Body SAR Compliance Testing, For that, we are trying to communicate...
Thanks in advanced. Platform is: nrf52832-qfaa, SDK_17.0.2. I use microusb interface as multiple port for charging and uart I/O. I always get APP_UART_COMMUNICATION_ERROR...
I was trying to build the ble_app_uart_pca10040_s132 from the nRF dk 17.0.2 examples and the unmodified file failed to build. I got the errors "unknown type name 'nrf_drv_uart_config_t...
Hello,
I've got a simple humidity/temperature sensor I am using, just to test out TWI on the PCA10040 Dev Kit.
When I wire up the sensor to the default SDA and SDCLK pins...
I'm using nRF5 SDK for Mesh v5.0 and I'm evaluating the Provisioner example to provision a node with sensor server model .
I want to modify the default publish period of...
Hi,
I'm currently testing the nRF52833-DK with the light switch example and it works great so far with the new Mesh SDK,
but I have still some open questions about the...
Hello,
I am trying to program my nRF9160 DK v0.9.0 with mfw v1.1.4 but I am getting an error "Modem DFU failed with error: Error: Error occured when program. Errorcode:...
Greetings,
I have two nRF52840's where one is modeled as a peripheral and the other as a central. I have created a custom service and characteristics on the peripheral...
hello Nordic
i work with nrf52840, SDK16.0 S140
i use QSPI for writing to an external flash (IS25LP064A)
if i write 16 bytes then its all ok but if i try to write...
Hello,
I have nrf52810 with soft device S132 5.1, SDK 14.2.
It works fine when NRF_LOG_ENABLED is enabled, data from NUS are printed in debug console. But Im not able...
Hello,
I am writing a BLE central application that connects to a device and should then discover ALL services on the device. I am new to Nordic and am using the nRF5340...
