Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi Support,
I am observing something that is quite strange on the GPIO input. I am developing a Zigbee device with Energy harvester with NRF52840. I need to use the state...
In addition to uarts, I2cs and SPIs I tried toggling some apparently spare pins without seeing voltage changes on the pins I tried.
Which pins are available for digital...
I'm using the Nordic nRF52840-DK board to breadboard an SDHC card interface in Zephyr using SPI. I have it doing "basic" operations, but am trying to reconcile what I'm physically...
Chip - BT832AF (nRF52810 QFAA)
SDK- nRF5_SDK_17.0.2_d674dde
SD - s112_nrf52_7.2.0
2V- power supply
My application need not to be very fast, but is extremely concerned...
Hi,
I am working on a project with 2 nrf52840 devices. One is the nrf52840 dk, while the other is a custom board with the nrf52840 module. I want to perform a dfu over uart...
I think this is a very weird requirement
Normally , I use manufacturer data to do this like picture below
it's easy and quick
but it contains len and type occupying...
Hey,
I am trying to get the Asset_tracker_v2 running on my Thingy:91, but with my own Cloud connection (It is a Thingsboard CE hosted on an ubuntu Server in Open Telekom...
I have to execute some lightweight error correction codes (ideally BCH) to compare and subsequently correct the mismatches between two binary arrays. I am working on the nrf52840...
I have been testing lte_lc_init_and_connect with my units inside a Faraday cage, This method doesn't terminate when it cannot get a signal (at least I haven't seen it). This...
I am attempting to install the nRF Connect SDK v1.5.0 on Mac OS X Big Sur, I have followed the Getting Started Assistant and Toolchain Manager with no success.
Here is my...
Hello everyone,
I am going to Integrate Bluetooth mesh into the nRF5 SDK example by using SDK 17.0.2 and SDK for Mesh V.5. I followed the instruction mentioned on the Infocenter...
I am from India. Recently I have purchased Thingy91. I have registered IBasis SIM as mentioned in the user guide. While registering the device in the nrf cloud I am facing...
Kind folks,
Attempting to install the Nordic Connect SDK again after failing several times before. (Always seem to have something slightly wrong in my installation which...
Is it possible to have 2 timers (TIMER3 and TIMER4) with the exact timer value?
I need to have two gpios toggeling at a difference time frequency but based on the same clock...
