Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello Nordic,
I try to establish communication between an ATmega328 based board an an Arduino Nano, so far without success. The goal is to improve a RF433 "Wire". 3 weeks...
Dear All, I am using the ADC to measure 3 voltages applied on different ADC inputs and 3 different channels. My ADC configuration looks like this: And this is how I am performing...
Hi,
I recently acquired the nRFgo starter kit and nRF2724 rev 2.1 and the nRFgo development kit. I have downloaded all of the supporting software that were found here...
I have the latest nRF Connect for Desktop.
After I install "nRF Connect SDK v1.4.99-dev1" in Toolchain Manager I don't have an "Open IDE" button.
I've tried uninstalling...
I am adding JLINK_MOITOR.c and JLINK_MONITOR_ISR_SES.s and add write
#if CONFIG_JLINK_MONITOR_ENABLED NVIC_SetPriority(DebugMonitor_IRQn, _PRIO_SD_LOW); #endif
at starting...
Hello everyone,
I'm trying to develop an application with BLE, using an example as a base.
The advertising is good, well configurated, I can edit manufacturer specific...
I am currently using Mesh SDK 4.2.0 and I could successfully write and read reliably from the flash using a second flash manager instance used in parallel with the flash manager...
HI，All:
the softdevice.hex has inlcuded the bootable/strat code,as the figure below ,how to separate the bootable code from the hexcode?
in the SEGGER IDE:
in...
Hello,
I am working on nRF52820 custom development board with nRF5 SDK 17.0.2. I am using FreeRTOS and I experienced a lot of problems with compiling a simple project. I...
Hi,
Currently I work on an NRF51 DK, by mistake I replace my bootloader by and .hex or .bin file with a drag and drop.
The LED 5 don't blinking and my computer don't...
Hi Dev zone,
I am working with the mqtt sample program using NCS1.3.0 and with a Nordic Thingy91.
I am able to publish and subscribe to the data , and I am using Mqtt...
I'm testing the nRF connect SDK 1.4.2 HID keyboard example (nrf/samples/bluetooth/peripheral_hids_keyboard) on an nrf52dk_nrf52832 and it doesn't seem to work. I have it open...
Using segger nordic edition I cannot unset the breakpoint for the first instruction in the main() function. Since I'm using zephyr with wireless on this board it causes a...
Hello,
i have an application with soft device 112 and libuarte_async on nrf52811. Everything working well when I'm sending small amout of data.
But now i have a task to...
Hi! We've been trying to get into development with Nrf52840 Dongle using Node.js / pc-ble-driver-js.
We have two dongles, and we just tried to test the heart rate examples...
