I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi.
I'm trying to integrate the MPU9250 with nRF52832 using i2c (TWI) on my nRF52-DK
I have found various libraries but none of them are working on my hardware. All of...
After several record updates one by one I get FDS_ERR_NO_SPACE_IN_QUEUES. However after each record update I wait for FDS_EVT_UPDATE event. I was sure that waiting for this...
I have %XRFTEST working on the 9160 in every band listed in the datasheet other than Band 14 and 17. Is there a reason these bands are not supported with the test mode?
...
I'm looking into integrating the SoftDevice controller (not full SoftDevice) from nrfxlib into NuttX RTOS. NuttX would already provide the host layer so I would only need...
Hi,
We are evaluating use of the NFC functions on our nRF52840 - based solution (currently we use BLE). I have been able to understand how NFC Tag payloads are setup within...
Hello,
Is calling --eraseall before calling --program the same as combining --program with --chiperase?
Does --recover erase all the areas that --eraseall and --chiperase...
Hi Dev team,
I am working around with the Thiny91 and wanted to have more information regarding the power consumption characteristics of the board.
I have a program running...
Hi,
Please clarify how RF performance degrades from 3.3V (PS) to 3.1V (3GPP), referred in nRF9160 Hardware Design Guidelines v.1.0:
3.1.2 Voltage range The operational...
Hi, I am getting error from socket() function. I cant find definition for AF_LTE family. I am using simple socket() as:
socket(AF_LTE, 0, NPROTO_AT);
It will compile but...
Hello everyone,
I'm having an issue of trying to connect via NRF Connect to my nrf52840 DK boards, but I am encountering the following error messages.
Core0: Error while...
Hi, I want to add an FTP client to my Zephyr projects. I am using an nRF52840-DK with a Quectell BG-96 modem. I want to upload and download large files using PPP protocol...
Hi,
We are developing an application on a nRF52840 using the nrf SDK (16.0) which should connect to a nRF52832 device , read characteristics of two different custom services...
Hi. We have developing a IoT board based on nRF9160 and faced some strange issue. We have realized the reset schematic of nRF9160 in this way
The nRESET pin is pulled...
Hello,
I am using a third party chriptographic engine that provides a dedicated hardware accelerator for AES-128 encryption based algorithms.
I am using this engine to...
Hi,
I am working on SDK 15.2, s132 on NRF52832-based board.
I would like to use the automated tests like here to connect to my devices and do some tests.
My device is...
