I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I know that we have actually some countries in Europe which don't support LTE-M, therefore we like to have a fallback.
Does there exist a fallback option to GSM or EGPRS...
Hi,
So I was having an error which caused my application to stall in the "do_stop_check" part of the nrf_drv_twi.c file, so I added a bit of code to check if I could figure...
We have a device with the following configuration:
nrf5_SDK_for_Mesh_v3.1.0
nRF5_SDK_15.2.0
s140_nrf52_6.1.0_softdevice
mesh_bootloader_gccarmemb_nrf52840_xxAA ...
Hi,
I'm trying to make a script in Python using the nRF52840 dongle, to make some BLE advertising.
I'm using:
- Python 3.7.2 (32 bit)
- pc_ble_driver_py library
...
Hi everyone,
I'm using ses IDE to debug via J-link on nRF52840 DK.
I'm debbuging CDC ACM example ( I haven't changed it ) but when I debug: ret = app_usbd_cdc_acm_write...
I am designing a PCB for the nRF52833 aQFN chip. To reduce the cost of the PCB I would like to fanout the inner row of the IC package on a single layer by using 3/3mil traces...
Hello,
I have a certificate attached, but in my personal account it gives an error when I enter the DK data.
Please tell me why the error occurs?
OS: macOS 10.13.6 ...
Hi,
I am using IM69D130 MEMS sensor with nrf52832 I just want to confirm the output of pdm sensor . please any one suggest how should i proceed . how do i code for it ?...
I am attempting to migrate my BLE project to a higher security level with bonding. Was mode 1 level 2 and am upgrading to mode 1 level 4. When I change the configuration to...
Nrf52832 chip is used, and the software package is the “nRF5_SDK_16.0.0_98a08e2” version.
According to customer feedback, Bluetooth connection is generally unstable...
Hello
I've seen several places that it is posible to build the project using jenkins, and hook Jenkins to the git repo where our nRF sourcecode resides.
Unfortunately...
Hi,
I am testing the USB CDC with nrf52840 and I want to receive a predefined array of bytes over USB serial every time I send a specific array of bytes.
Just a simple...
