Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello I have an application which advertises permanently on the Bluetooth but I would like that under certain conditions, that they advertise another name. Can you tell me...
Hi everyone,
In the USBD example we use ENDPOINT IN 1 to comunicate (if a button is pressed) with the host the position of a mouse.
I modified this example, I don't need...
Dear Sir.
In my program 2 strings I need to protect when a new firmware is updated.
#define PROD_DATE "PROD_DATE_03_12-2020" #define IRON_NUMBER "IRON_1234567899999...
Hello,
In my application I use NRF52840 with SDK 16.0.0 and softdevice 7.0.1. I want to add ECDH algorithm to my project using ECDH example in the SDK, but nrf_crypto_ecc_key_pair_generate...
Hi there,
I'm presuming that, when using the s140 soft device (or any of the soft devices), I cannot change the output of VDD to anything and must assume 3V.
I have tried...
PWM frequency and PWM steps resolution are related, we increase one and the other decrease and vice versa, we want high PWM frequency so we have low flickering and we want...
Hi everyone, after months of working with the nRF52840 dongle I decided to buy the nRF52840 DK. I work with the ide SEGGER EMBEDDED STUDIO. I tried to get the blinky example...
Hello,
I can smoothly run the sensor server / client model. I know that I can setup the periodic publication period with the nRF Mesh mobile app and don't have a problem...
I want to configure 32bytes sensor measurement data in advertise manufacturer specific data as follows.
But does not work, please help me.
My environment as follows. ...
Is there demo for video transmission on PCA10056 DK?
it is just video transimission demo. just loopback is ok.
we are using nRF52840. is it possible？ or other platform...
Dear Mr/Mrs,
I am learning to develop an Android BLE apk. I use the nRF Connect apk and Android-nRF-Toolbox to connect with my BLE device.
nRF Connect connect to the BLE...
I have an found a problem where I find FDS has 2 pages labeled as swap, which results in loss of one of the data pages.
my configuration is 2 data pages and 1 swap page...
Hi,
I modified the USB BLE example (nRF5_SDK_17.0.2_d674dde/examples/peripheral/usbd_ble_uart) to sends bytes using a timer timeout as "fixed bytes transactions" or "waits...
Hello,
We have a custom board designed using the ublox Anna B112 module which uses NRF52832. We are using it in open CPU mode and running our custom firmware.
The VDD...
