I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, everyone
I am developing a BLE product with NRF52840 base on SDK 15.2.
Due to the cost of the product, we are now evaluating the feasibility of migrating from NRF52840...
Hi,
I am testing curve25519 in M52810.
The following is snippet.
nrf_crypto_ecc_curve25519_private_key_t bob_private_key; nrf_crypto_ecc_curve25519_public_key_t bob_public_key;...
Hi Dev Team,
I had a task to work on that required a timsetamp to schedule a certain event, like for example I wanted my modem to start off every morning at 10:00:00 and...
Hi,
I am using Thingy 52 to measure the acceleration from accelerometer. I was expecting values like m/s2 but I am seeing values in unit vector, ie, values between (0 -...
I have nrf52dk (nrf52832) board and a custom nrf52805 board. The nrf52805 board has no external 32kHz crystals, but only 32MHz crystal. Also, it is in LDO mode (no DC-DC inductors...
Device nrf52832, nrf5_SDK_for_Mesh_v3.2.0_src with nRF5_SDK_15.3.0_59ac345
Hello.
I want to transmit and receive some data between smartphone app and mesh sensor.(almost...
Hi, Im using nRF52840 DK, Segger Studio v4.52 and SDK version 17. I have been trying to make BLE OTA DFU work but have had many problems along the way. I followed the guides...
Hi folks,
I need a production test of an nRF52840 module at PCB level. Our board connects near instantly with nRF Connect + Bluetooth Low Energy, and displays its device...
Hi,
I am trying to implement wireless power transmission. For sending output voltage information from receiver board
to transmitter board continuously which of you module...
Hi, I am getting link time error in segger when i building a pre-built library with zephyr for NRF5340.
Error says,
c:/gnuarmemb/bin/../lib/gcc/arm-none-eabi/8.3.1/.....
HI. I have modified "usbd_ble_uart" a little bit and have changed the BLE service for transfering the received data from USB over BLE. The problen is now, the BLE service...
I am working with the nRF52840 DK and was looking for a way to set a compare register to trigger at 300 ticks, and another to trigger at 40000 ticks. The register that triggers...
Hi,
I am a new comer so perhaps I made a mistake during project configuration.
I am using nrf Connect v3.4.2 on Windows.
I trie to add CC310 libray in sample hello_world...
