Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I'm doing some clean up in my code and i wanted to use only nrfx library as it advised to do. Regarding the watchdog i have set in my app_config.g file (used by my...
Hi,
Right now i am working on mesh sdk 3.0.0 on segger embedded studio and board i am using nrf52832. In my application i am trying to implement the watchdog timer but it...
Hi,
I want to use the nRF52832 on a recording system for sending the data to computer using BLE. I want to receive data after a while that the system is put in its position...
Here is my function to generate random numbers of desired length.
After generating a few(5 to 6) random numbers the function hangs at .
I am using RIOT OS on nrf52832...
Hi.
Hope you are well.
I intend to use the nRF52832 for a wireless neural recording system and I need the nrf to do some works for me, such as:
1. putting the system...
i am using nRF52832 with Mesh3.0.0, i want to build a network like a chain,Client1 to Server2 to Server3 and Server4 with interval about 40 meters, however i tested with light...
Hello,
Our team are evaluating the nRF52833 vs the nRF52840 and would like to understand the following
1. The nRF52840 clearly state that its RNG hardware is NIST SP800...
Windows 10, Segger V4.52c, S132, SDK 15.2.0, nRF52832
I'm trying to add Peer Manger to the UART template. I included all the C files from a tutorial I found and enabled...
Hello.
I am using nrf52-dk with 52832 (PCA10040).
To check the current consumption, I made a simple test.
I need to wake up every 5 seconds, do what is needed and fall...
I am currently working on custom firmware hosted by the nrf52832 SoC on a custom PCB. The project is built with a makefile and armgcc, using the "nRF5_SDK_15.0.0_a53641a"...
1. The use of the sdk is: ncs v1.2.
2. The routine used is: asset_tracker.
3. Test failure code see annex: 4_asset_tracker_ram.
4. Applying 100KB of memory on the 10_hello_world_ram...
Hi, I'm just getting started with Nordic SoC. I have two nrf52833 DK and would like to test the long range (125K and 500K) from the examples provided (precompiled hex). After...
Hi all,
I'm trying to build the hex files for the pc-ble-driver and am running into build issues.
My Setup
I'm running a Linux (Ubuntu 18.04) VM that I also currently...
Hi Everyone We are using nrfx_uarte library to implement the uart functionality , Everything seems to work fine with the uart , but the problem comes when we want to have...
1、Can BME680 be enabled for air quality testing? There is no initialization function to get air quality, and the function to get air quality data returns -1.
2、The gps_handler...
