Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am trying to add the tensorflow lite to a segger project. I am startting with the simplest project https://github.com/tensorflow/tensorflow/tree/master/tensorflow/lite/micro...
I am keep trying to get the BME680 example to work with the nRF52840-DK using Zephyr.
I check and successfully find the node for the BME680, but "device_get_binding()" for...
Hi,
I am using
I am able to list BLE devices using the below example.
SDK = nRF5_SDK_15.3.0_59ac345,
Example : nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_gatts...
According to this thread, iPhone 11 Pro supports Long Range (Coded PHY) : https://devzone.nordicsemi.com/f/nordic-q-a/33060/is-there-any-smartphone-with-supporting-of-bluetooth...
Hello,
I am upgrading to SDK 17.0 from 15.0.
When I try to to compile my project i get this error:
../_Release/Release_Commercial_Debug/Main/Exe/Main.elf section ...
Hi,
I followed the tutorial in the Github and create a custom service. (Github: https://github.com/NordicPlayground/nRF52-Bluetooth-Course )
1. I use the ble_cus_custom_value_update...
I have an issue with my Thingy:91
1) I unboxed
2) I successfully connected to my Windows machine and updated the modem firmware
3) Turned off power
4) Turned on power...
I would like to add a simple ble BAS (battery service) to appear along side my custom services... but for the life of me I cannot find any information, or tutorial on how...
I build project without problems, but this simple sample return zero results for read buffer. I return 5 zero from 5 zeros. I have right names for overlays files. nrf9160_pca10090ns...
I'd previously run into this problem with mqtt_publish not being able to handle large payloads, larger than approximately 2k.
At the time, the suggested workaround was to...
Hi All,
I am working on a project where i need to communicate using i2c protocol. For this i need to set i2c frequency 20 Khz. So how can i calculate register value to set...
software : nRF5_SDK_14.0.0_3bcc1f7
hardware :nrf52832qfaa
example : ble_app_hrs_rscs_relay
i want use "example : ble_app_hrs_rscs_relay" to receive more then 20 byte...
Hi all,
I have a DK 10056 rev 1.0.0, and it suddenly stopped working on the Embed side. Using the USB port (the DK one, not the NRF one), the LEDs (4 LEDs for testing purposes...
Hi,
I am using an nRF52 based chipset and programming the device with the hex file.This is being performed using the nRFConnect v.3.4.1 Programmer. The erase and write option...
Hi,
I have a custom prototype board based on nRF52833 which runs a working firmware and I have not any other prototype ready to hand.
Unfortunately, I think that the source...
