Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
When designing an NFC coil to use with the nRF32832, are there any recommendations as to the coil inductance and Q that we should target?
Being a passive design, we are...
Hi I am using the tutorial from https://github.com/bjornspockeli/custom_ble_service_example . I have uncommented some of the starter code from ble_cus.c. My understanding...
I am inquiring about something I know very little about but will try to communicate for the information. Smart phone applications can be opened through a QR code which utilizes...
Hi,
We are using ncs tag v1.0.0.
I am using i2c_scanner example firmware. It works find when used as it is.
When I added "UART2" in this firmware i am getting hard fault...
Using the ble_app_uart example, Using oscilloscope to measure the time interval of broadcasting, two development boards are used respectively. One development board is nrf51422...
Hello, rols and hkn:
I got two different answer about watchdog and hardfault in devzone.
1. watchdog can't reset hardfault. https://devzone.nordicsemi.com/f/nordic-q-a...
https://github.com/bjornspockeli/custom_ble_service_example
I am currently following this example with SES on my NRF52840 DK (PCA10056). I copied the ble_app_template example...
Are there any recommended alternatives (& nordic plugins) to the discontinued Bluetooth Developer Studio? I'm looking for a tool to make the process of creating custom GATT...
Hi! I want to copy data from internal flash to a statically allocated buffer in RAM. I get a DACCVIOL hard fault try to do this by memcpy. The hard fault depends on the number...
I need to send 5 sensor values received over SPI to an app over BLE about 5 times a second. I also need to send a few configuration parameters from the app back to the nrf52...
I am using nRF 52 DK connected to Arietta with ARM Linux (4.2.6) 32 bit.
when I was trying to install "vcpkg" using "./bootstrap-vcpkg.sh", I am getting some errors as shown...
I have a phone app which talks to my peripheral device running the nrf52832 and so I will eventually add another peripheral device which ideally can communicate directly to...
Hello everyone!
I'm working on a project where there are 2 microcontrollers: the Nordic nrf52832 and a 3rd-party uC (can't disclose it). A protocol to transfer the firmware...
I feel confused about bearer. what's the difference between mesh-bases bearer and PB-ADV bearer or PB-GATT? there is little knowledge about mesh-bases bearer within mesh profile...
