Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’. Currently it is SystemON mode. But I need to change...
Hi,
I am having trouble running the ANT+ examples on the 15.3 SDK. I'm testing on a NRF52832 DK (PCA10040) and I'm trying to get the ANT+ examples working on SDK 15.3, in...
Hi everyone
I was testing the bonding with MITM settings. I used the code from the following link: github.com/.../nRF51-ble-peripheral-bond-handling . I tested the bonding...
Is it possible to generate a pre compiled library that configure at run-time new BLE services and characteristics on the nRF52840? If the answer is yes, is it possible to...
Excuse me, I have a question on calling external function.
board using: nrf52832
softdevice using : s132(6.1.1)
The situation: There are two applications which is...
Hi
I am using PCA10040 in order to develop nrf52 firmware. For now I would like to try to measure current consumption.
Is there any couple of pins on the board I can use...
I've been doing some testing with the nRF52840 (I purchased the Raytac MDBT50Q-1M), and I'm seeing a pretty hard startup surge. I've attached the results from my scope. The...
Hello,
I have some problems when running the development kit. It seems the problem might be somewhere on the PCB, something related to power sources and power distribution...
Hello,
I try to make my NRF52832 communicates with a memory (MX25R1635FZUIL0) in SPI.
When I try to read the memory ID, the RX buffer is fill with 0x00. But when I observe...
Am facing issue when am reading data from controller(UART) and using ble_app_uart example code to send data to BLE.
Not able to use two uart's at a time.
My setup: nRF52832 with nRF6707 on top. My embedded application synchronously exchanges UART messages with a desktop application that feeds it data (on demand from embedded...
I use nRF52DK as a central using ble_evt event BLE_GAP_EVT_ADV_REPORT to get RSSI from the peripherals when they are advertising. But once the connection is established, how...
Dear community,
I'm having some trouble configuring and adding subscription addresses to one of my node's Generic On Off Server model. This devices is composed of the usual...
I am new to GATT services and characteristics. I have written one custom service with two characteristics for my custom board. I have used nrf 52832 with sdk 15.2.0 and referred...
Hello,
I am trying to connect to my nRF52832 through J-Link v6.22g. This version doesn't contain the RTT Viewer GUI, but instead I am trying to connect through the RTTLogger...
