I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have a custom PCBA running my development firmware. When I turn everything off (meaning no peripherals are active - most chips are in sleep mode or de-powered; BLE disconnected...
Hi
Can I use app_timer with APP_TIMER_CONFIG_USE_SCHEDULER set to 1 when using task manager?
Setting APP_TIMER_CONFIG_USE_SCHEDULER to 0 causes the timer to fire, but...
Hi,
I am using SDK 15.3.0 for nRF52840.
We don't want to use peer manager and id manager as we don't need bonding.
We added the remote device with public address type...
nrf52832 SDK14.2 s132_nrf52_5.0.0_softdevice PCA10040 ble_app_hids_keyboard
I m odify the proj ect :
two service : one is hid another is different hid_1
press button...
Hi!
I have been trying to observe the NRF_LOG_xxx output in my Eclipse console on debugging mode. However, nothing prints in the console (image 1).
I tried enabling...
Hi
Befor I used nRF51822 to transmit a packet per 5ms, payload length is 12. I can received 200 packets/s, Initialization settings are as follows
Device : nRF51822...
Dear all,
I have been struggling with updating my advertisement data package in SDK15. Using Jimmy Wongs's example ( https://github.com/jimmywong2003/nrf5-modify-device...
Hi,
to initialize the button properly
to trigger the push event on button push and the release event on button release, do I just have to change the button active state...
Hi there,
So I am trying to get a basic mesh setup between multiple Nordic Thingy 52's and no matter what I have tried i keep failing,
I have gone through the forums...
I have an Adafruit Bluefruit Feather nRF53832 board I am considering using and need to change the default serial baudrate from 115200 to 9600.
I am told that I can use the...
Hi:
I am using a shake sensor as an analog input wake-up system. The system is not system off. The analog input signal only generates an event to wake up turn on...
I am using the UART central, integrated with peer manager and UART peripheral application from the SDK 15.3 on our custom hardware. I have 2 centrals running exactly same...
Hello everyone.
I want to familiarize with The Power Profiler Kit. I've installed proper software and been trying to connect to the device but every time I receive the same...
Hello,
I am trying to load the ble_app_hrs example from sdk15 on to my external BMD-350 module, but I cannot seem to discover the module using nRFConnect. I am not using...
SDK:
nRF5_SDK_15.2.0_9412b96
Softdevice:
132_nrf52_6.1.0_softdevice.hex
Hi Sir,
I want add NUS function to ble_app_hrs_rscs_relay sample code and I add...
