I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
SDK:15.2 KeilC:525 SoftDevices:s140_nrf52_6.1.0_softdevice Hardware revisions: PCA10056
I have try the multiperipheral in 4 smart phone connection in blinky App. But I need...
Using nrf52832, SDK12.30 demo project ble_app_uart, testing with nRFconnect app.
Load ble_app_uart demo to board and run. Open nRFconnect on smartphone scan, and connect...
Hello,
I am encountering a small problem with my timer, I followed the tutorial : devzone.nordicsemi.com/.../application-timer-tutorial
The purpose of my project is to...
We have been using SDKv11.0.0 with S130 softdevice on nRF51822-QFAA rev 2 on a custom board with no problems at all.
Since our nRF51822 BLE module vendor no longer support...
Hi guys,
I flashed the mbr hex file and then the open bootloader to a custom nrf52840 board. When i first connect it, it boots into the bootloader mode and i am able to...
Hi,
I need to use
p_status->action == RELEASE_ACTION
to set the brightness level, but the p_status->action only gets updated after the loop finish so:
if (p_status...
Using the Border Router Quick Start Guide I've created the following setup.
2 Raspberry Pis, each with their own nRF5280-DK running RaspPi_OT_Border_Router_Demo_2.0.0...
Hello,
I am using nrf52840 with OpenThread stack. While I am using FDS to store application data, it seems the OpenThread dataset is written in the same area. Thus, the...
Hi to all. We develop new battery sensor based on nRF52832.
We already have an experience with Li SOCL batteries ER14505-VB 3.6V, and satisfied with it. Have in stock also...
I use sdk15.2. bootloader nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_ble_debug. Application nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_buttonless_dfu...
Hello, I'm currently attempting to display a screen during an OTA-DFU process. First and foremost, through BLE, a BLE Central will command my BLE Peripheral to commence DFU...
I am working with NRF52832 master with TWI slave device, however , since our board already has external pull-up resistors (10K) , how do I disable TWI internal pull up resistors...
Hi nordic
I am using SDK 14.2.0 Softdevice s332 5.0 Board nrf52840.
I am doing test about DFU example and I am writing in flash about test image.
It is possible. I made...
Hello.
We have a working DFU system using Nordic's Secure Buttonless DFU bootloader. The bootloader correctly checks if the incoming DFU package has the correct 'init packet...
Hi all,
I am curious about the storage capabilities of the Nordic Thingy. I would like to store information about the received messages like a timestamp. How much data can...
