Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello, community!
I'm currently trying to set up a Xiao BLE module (based on the nRF52840) for development using the nRF Connect extension in Visual Studio Code. I've been...
I am making an application using nrf52840 USB dongle.
I am using a python program with pyserial. This works great. My only problem is that I want to have a very reliable...
Hei I am trying to make SPI or UART communication between nrf9160 and nrf52840 on thingy 91....... i need to send data from nrf52840 to nrf9160(i will use and print the data...
Hi!
One of the requirements for EN 18031-1 is that a product shouldn't contain publicly known exploitable vulnerabilities:
6.10.1 [GEC-1] Up-to-date software and hardware...
I have problem with one question of the lesson 5 Quizz of the "nRF Connect SDK Fundamentals" course (Dev Academy)
https://academy.nordicsemi.com/courses/nrf-connect-sdk...
I am running the examples l9_e5, l9_e5_sol and l9_e5_nrf5340_both_sol from this repository: https://github.com/NordicDeveloperAcademy/ncs-inter/tree/main/v2.9.0-v2.7.0/l9...
Hi,
i am working with the following setup:
- nrf5340
- SDK 2.6.3
- Direct Test Mode example with serial communication
I see that DTM example has changed from 2.1...
Hi Nordic team,
I'm implementing a BLE UART bridge (emulating the old SPP profile) using a custom service. The central device (dongle) I'm using only supports the classic...
Hi guys,
I am following DevAcademy lessons on nrf52833dk kit. I am testing the software on VsCode. SDK version is 2.7.0 and toolchain is 2.7.0. Board target is selected...
Dear, I'm developing on nordic 52840 with ncs2.6.1.
I found that the Current will reach to 600+uA in k_sleep state by enable SPI in device_tree and if i disable the spi...
How do I adjust the swd speed used by nrf connect RTT ? Currently it is 2000khz but more is needed. I need to transfer audio data to PC.
For some reason my current process...
Hello,
I am attempting to configure the following setup to support (with an nRF5340 + nRF7002-EK)...
1. nRF7002 on SPI w/ TLS, STA, and FW patches offloaded to QSPI...
Hello,
I am using PAwR (Pe riodic Adve rtsing with Response) in coded PHY (S8) with SDK 2.7.0, following the Nordic demo :
8562.PAwR_Demo.zip
Periodic Advertising with...
Hi all,
I'm working on a BLE peripheral using Zephyr and have run into an issue when enabling both dynamic device naming and long advertising intervals.
I enabled dynamic...
