Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
As a brief introduction, our research group uses bluetooth advertising to broadcast commands and responses between end devices and 'routers' which are connected to a PC. ...
Hi,
BLE Application on nRF52840 (pca10056) development board is being developed.
Application stopped the advertising to make device non-discoverable.
After that trying...
SDK 15.2, API 6.1
I have 1 firmware and 2 PCB it operates. PCB A was an external crystal and the sdk_config file is setup for the operation. However, PCB B uses internal...
I would like to communicate with and existing product that has the ability to communicate thanks to a UART-Bluetooth module. This module uses a Serial Port Profile and shows...
Hi,
I'm working on a thread network and I have some difficulties to configure the BorderRouter.
I use the BorderRouter V2 rapsberry image from Nordic, I recompile the...
Hi,
I want to be able to update the bootloader along with the application via OTA DFU. I know I can't generate both the application and bootloader in one image/zip so I...
I am looking for specs for the input impedance of the comparators (COMP and LPCOMP) for the nRF52832. I searched the forum and all I found was someone saying it is ">1 Mohm...
Hi,
I am trying to incorporate flash storage library to ble_app_uart_c example. I have added all necessary functions from ...\examples\peripheral\flash_fstorage.
When...
Hi everybody
I have a couple of questions regarding power consumption for the 'nRF5_SDK_11.0.0_89a8197' (nRF52832).
I currently have an application which use 12-bit SAADC...
Hi, I made a simple diagram of what my device should do:
The nRF52840 should receive data via SPI from another controller, mathematically process this data, and output...
Hi,
I just pulled the source code of 'nrf' from the git server (SHA1 ID: 383da27cc232bd7baa353e965b7fe8fa08b56d77).
After performed 'west update' to sync other repos,...
Hello!
I want merge and write via SWD full firmware, including: main firmware, bootloader, settings page.
When I start debug, all data correctly writed, but main firmware...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
Hello,
My device has GATT data attributes configured to have BLE_GATTS_VLOC_USER so the data are in application stack. In this way, the softdevice has direct access to the...
I've been trying to use the Adafruit nRF52 library ( github.com/.../Adafruit_nRF52_Arduino) and the Arduino IDE to program a nrf52832 using my nrf52840 DK. However, I keep...
