Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I'm currently using nrf8001 to send data to my phone. To save power from the peripheral device, I wanted to change the connection parameters.
I set the min and max connection...
Hi, I'm using nRF52832 with my external board.
I'm recently working ble uart example.
I control motions with tx message such as LED, motor and so on.
Now, I want to...
Hi,
I need to set a client back to the state, when its flash was erased and programed, so if I understand this correctly, the provisioning data has to be erased.
How could...
I've been developing on the PCA10028 development kit with print statements working fine (though at the moment it seems only SEGGER_RTT print statements are working and not...
Hello,
I am getting an error message while I was compiling the "ble_nfc_pairing_reference" example. How can I obtain this " micro_ecc_lib_nrf52.a" file ?
Fatal Error...
Hi,
I'm trying to edit the nfc message in software but after a while the nfc stops working.
What could I be doing wrong? This is my code, I change the value every second...
I have a project that I assume was originally set up with SES on Windows. I need to build it with MacOS but I get an error 'sdk_errors.h file not found.' I assume this is...
Hi，
I finally want to integrate BLE and 2.4G in nRF52810.
【1】I am studying Timeslot，i found some articles in DevZone.
There is a mention of micro-ESB ， so what is micro...
Hi, I am currently testing some BLE sample code (the proximity code and hrs code) with the nRF52840 PDK and I am trying to just simply interface the GPIO interrupt example...
1. How should I connect with UART to my board?
2. How to put the device into RX mode as required by RED EN300328?
Test the Radio Test Example application by performing...
Hi,
My problem described below, please share solution or any suggestion how to fix this.
=== Background / Problem ===
I've setup and run MESH serial network, for machine...
If I use RTC and Timer simultaneously, getting fatal error as timer disables RTC. Is there any way by which I can use both application and RTC in my application?
Our device is implemented as BLE peripheral device and based on nRF52832
For saving space in Flash memory we try to downgrade SD version from S132 v 5.0 to S112 v 6.1.0...
Hi,
I am doing one more project in that project I want to do following things:
1) my one BLE giga device module(nrf51822) will act as a master(central) & other AT command...
