I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, We made a custom board using the NRF52832. Everything is working in our system except BLE part. We are using SDK 13 with Softdevice of S132 v4.0.2. We tried to flash examples...
I'm using SDK 14.2, S132, and the NRF52832
This problem occurs during the pm_init() function when initializing the soft device. Investigating further has led to the pages_init...
Hi, I've been tasked with sending commands to an nRF52840 Board via a React Native mobile application I've developed, but have no idea how to do so. Our company uses:
...
Hi all,
I would like to learn how to use the USB peripheral these days. So, I programmed the example of usbd_cdc_acm on PCA10056. The PCA10056 couldn't be identified after...
nRF5 SDK structure project use makefile and sdk_config.h header file, When I want to add a component to my project. There is too hard work to modify the makefile and sdk_config...
Hi everyone,
I am trying to understand this sample code: here
But I don't understand how to choose an arbitrary pin for the LED.
And also, in LED_MASK which pin is...
Hi,
I recently dug into the potentials of the NB-IOT network allowing iot devices to directly make use of cellular communication. With the release of the new nrf9160 containing...
Hi,
Recently, I was trying to pair the nRF51822 development board by windows swift pairing.
While I turn on the swift pairing function, I still cannot use this feature...
I have a similar question to https://devzone.nordicsemi.com/f/nordic-q-a/32115/how-to-parse-the-log-file-of-the-nrf-connect-for-desktop
There are lots of data in these log...
Hello.
Recently, our supplier recommend us to use nRF52810 instead of nRF52832.
These two MCU have same pin map, so just we pulled off existing nRF52832 from the board...
Hi,
we had used nRF52810 in our product. Our product is undergoing FCC & IC certification.
FCC & IC regulatory body had requested to provide Tune UP tolerance values of...
Hi There,
I was trying to understand the step to create a test app for dfu bootloader update via BLE for PCA10040. Below is the documentation I read.
http://infocenter...
Good day
My nRF51822 uses the Eddystone example with SDK 12.3.0 in conjunction with S130. When I configure TLM in slot 1, I notice that the temperature is about 6.5 degrees...
Installed nRF5_SDK_15.2.0_9412b96 and nRFGo Studio. nRFGo Studio fails to recognize the nRF52840 DK board. Screen like this:
It sees and correctly identifies the Segger...
