I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Sir/Madam,
I am developing application software using nRF51822 in keil microvision 5 IDE. I want to know how to download the hex file without using KEIL IDE. I found the...
I'm looking for an equivalent simple DFU bootloader over UART similar to the HCI example which was provided in the nRF5 v11.0.0 SDK.
Currently, I'm developing with the Sparkfun...
hi,i have a problem! How to Optimize code space in nRF52810,s112,SDK15.2.0,example ble_app_hids_keyboard.
my method is that disable all the code which run in main function...
Hi all,
Now, I have a troube. In Mesh 3.0, I want to advertising data. This is my function :
#define ADVERTISER_BUFFER_SIZE (128)
And whenever the data changes, I...
I bought a nRF52840 Dongle, to evaluate the use of nRF52840 for ZigBee purposes.
I have been able to flash such firmwares as \examples\peripheral\blinky\hex\blinky_pca10056_mbr...
I have a custom board where both nRF52840 and nRF52832 SOC in it.
i have flashed example Ble_Uart code from sdk15 in nRF52840 but im facing a serious issue.
i can able...
Tôi đang sử dụng bảng nrf24l01 để định vị trong nhà, nhưng tôi gặp vấn đề với định vị TOA và bảng arduino không đo thời gian nhỏ hơn micros, tôi không biết bạn có lời khuyên...
Dear Nordic,
I am trying to setup a custom BLE client service to interact with the Komoot app (Turn by turn navigation).
I can connect to the phone, and receive notifications...
Hello Team,
I am trying to run the example DFU overt TFTP, however I found the description a bit ambiguous. Seeking help to remove my ambiguity.
I am trying to follow...
Hi,
I am unable to program the nRF52 Dongle. What I see is that the "Write" option is not highlighted.
Though the Bootloader and Softdevice are already there on the...
Hi All,
I have downloaded the nRF Mesh SDk 3.0.0 and tried to run. I am trying to run the default nrf5SDKforMeshv300src\examples\light_switch\server for
Here is my software...
I have enabled the whitelist feature based on the ble_hids_keyboard example, but when I load the application it is not advertising anywhere. It is paired with my iPhone, but...
I am having one MDBT42Q device on which I am trying to flash an Example image of Peripheral to check basic functionality by nRFGO Studio.
In my device, I have sorted Pin...
i am trying to run advertising.py from pc-ble-driver-py .
i am keep getting exception from
except IndexError : raise NordicSemiException( 'board not found' ) is there...
I am looking through the BLE examples, but I can't seem to find an example that best fits my project scope where I wish to have a BLE central service that reads data from...
