Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello,
I want to use privacy (BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE) if the connected device support this feature. As far as i know it's not possible at application...
Hello,
My problem is that i have seen a reduction in throughput with android oreo in a huawei p10. Before the update i was able to send two notification per connection interval...
I use PCA10040 development board. COM port suddenly stopped working. The issue is visible also in Device Manager:
Google suggests that this issue is caused by Windows...
Hi
We have project where we want to use a nrf52 in an remote keypad for control various devices.
For investigating the capabilities I have tested the ble_uart and ble_blinky...
Hi,
I've been working on a project where I need to send data from UART over mesh, I managed to create custom model for sending string data over mesh, I did merge UART example...
Hello. I have SMARTMP3 Board and NRF52832. The vs1053 works fine on the arduino. But it doesn't work on the nrf52832. I use these connections: #define SCK_PIN 3 #define MOSI_PIN...
The NRF52840 appears to only come in a dual row QFN package and in the reference material, the only way to break out the second row is with an in-pad via or a very small trace...
Hi I am trying to use a different base UUID template than 0 x ABCDxxxx-1212-EFDE-1523-785FEABCD123.
For my services I would like to use 0 x xxxxABCD-1212-EFDE-1523-785FEABCD123...
From what I understand the clock source for the example ble_app_uart is the 32 KHz external crystal. Please, see the screenshot of the CMSIS configurator:
How do I set...
Hi all!
I use the ACM_CDC USB class to transfer a batch of data (150MB) from the MCU (nrf52840) to the host. Currently, the system reaches up to 100KB/s upload speed, although...
Hi @ll, I have the following problem: There are three unprovisioned devices with UUIDs containing a 0x0A byte but the scanner within the pyaci script shows 0x00 instead. Device...
Hi.
To avoid via in PAD I like to route a signal/pin from the inner row (closest to center) through a pin in the outer row.
However, to be able to do that I must be sure...
We are using SDK_13.0.0_04a0bfd and want to change the location and size of the bootloader in flash. But when we do this, the bonding process in the main application doesn...
I'm a newbie to nRF5... I just installed latest IAR, nRFgo, Segger J-link & nRF Connect on Windows-10. Segger J-link appears to have updated nRF51 Dongle to 6.3. I get the...
