I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
I know the Nordic provides timeout parameter to control advertising parameters.
If I set the ble_adv_fast_timeout to 1s, my ble-central device scanned the advertisement...
I can use standard UUIDs and successfully add a Service and several characteristics, so I think the error message above is a red herring. When I attempt to create a custom...
Hi there,
I am trying to modify flashwrtire peripheral example code for uart bootloader,
- I have used flash read write softdevice functions (sd_flash_read/sd_flash_write...
I am trying to program a BMD-300 over a serial connection through the RigDFU bootloader. The module has been updated to the latest factory image.
I can compile the application...
Now I want to run the python scripts interactive_pyaci.py in Embedded system device, I want to know which version of Python Environment must be install in the Embedded device...
I cannot find the call to sd_ble_gap_appearance_set(...) function in the ble_app_blinky example, so that I think it's unnecessary to call:
in nRF5_SDK_for_Thread_v0.11...
Hi!
I am using UART in NRF52832 with SDK15.0.0 to communicate with TCP socket via cellular modem.
I am using printf() to send the following AT command sequence to the...
Hi, I am using the Serial port library in SDK15. I am using the port in NRF_SERIAL_MODE_IRQ mode. After transmission the number of bytes receive are variable ranging from...
Hello. Im working with:
sdk14.2
softdevie ANT_s332_nrf52_5.0.0
chip: nrf52832
Problem: we have a product almost ready to be sold. We decided to start the migration...
Hello. I am trying using the nRF52832 with SoftDevice S132 v4.0.2 and SDK v13.0.0 along with the uECC.c/h files that I downloaded from github.com/.../micro-ecc . My device...
I know you can configure the threshold for low voltage that would stop writing to flash.
some people set this to 2.7 volts.
I want to know what the minimum voltage the...
I have followed the exact steps mentioned here http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v2.0.1%2Fmd_scripts_interactive_pyaci_doc_demo_configuration...
Hi all
I use nRf52840 with SDK 15.0. It allows SPI SPIS and TWI (i2c) ,but almost 3 items in the same time. I want to use spi0 as master to configurate my other mcu and...
