I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi Team,
I am using sdk12.2.2 and nrf52. I want to use one gpio to detect button state & have to operation on that event.
I used one method to configure(code snippet...
Following the guide found at : file:///C:/Github/STIWHN/SDK_thingy52/thingy_sdk_v2.1.0/documentation/firmware_compile.html#compile_gcc
I still getting errors trying to...
Hello,
For the softdevice update, is it the responsibility of the bootloader to make sure, that the softdevice was copied correctly?
If for example the bootloader calls...
Hi,
When i use FreeRTOS tasks with priorities 2,3,4,5 what i need to #define for XXX_CONFIG_IRQ_PRIORITY of SPI,SAADC and GPIOTE at the file sdk_config.h
Thanks
Hello, I use nrf51822 , sdk 8.0.0, s110
I defined advertise interval and timeout
#define APP_ADV_INTERVAL 320
#define APP_ADV_TIMEOUT_IN_SECONDS 3
Also, I write...
Hey Nordic Devzone,
I am really new to Nordic and am still a student in embedded software engineering. So first some background information.
I have 6x nRF52840 and 5x...
Hello,
I am designing a custom 2layered PCB board with NRF52832 IC. I have followed the reference design given in IC's datasheet as shown in the figure. Please provide the...
Hi,
I'm currently building a BLE multi-sensors device, with mbed online IDE. I succeed in implementing BLE API, and releasing a first .hex firmware with multiple services...
Hello,
I added an extra opcode to the DFU Control Point characteristic so that I can jump to the main application by writing to it. The problem is that whenever I do that...
Hi there,
quite a beginner here and tring to figure some stuff out about the nordic programming style.
when sniffing around the given examples in the newest SDK(SES...
HI,
I got 2 nRF52840 dev kits and I'm interested in testing the long range layer (LE coded PHY ) between the 2 modules, also scan for the second module RSSI value.
I...
Hello,
This is my first time working on BLE and Nordic, so this might sound strange.
I am trying to update data on the fly when the central requests char data.
I have...
Hello,
I am designing a 2 layer board with NRF52832 IC. I am following all design considerations and reference design mentioned in IC's datasheet provided by Nordic. I have...
Hello,
I am designing a PCB with NRf52832 IC. I have a query regarding the width of the feed line. In reference design files, the width of the feed line is 30mil. I have...