Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
We are trying to put togheter a custom mesh communication protocol based on nrf24L01+. Everything was good until we made transmission tests outside, from ground...
Nordic board nRF52 PCA10040, V1.1.1, 2017.1, 682048249.
The pins CTS, RxD, RTS and TxD are currently driven by the MCU. I want to use the SPIS0 in the nRF52832 with the pins...
Is there a Setting in IAR to program nrf52832 without Power cycling
nrf52832 does not start after programming from IAR IDE, using J-Link
But..
For both With J-Link...
I have been experimenting with using some peripherals on the nrf52832 without using the SDK. Primarily of interest to me right now is the low power comparator (LPCOMP).
...
i use nrf52832 .i want to connect device and send advertisment data at the same time. But peripheral mode cannot connct device and send advertisment at the same time. central...
Hi!
I am sorry if I had repeated questions in this forum. I would like to understand few things.
Test scenario
Central - nRF52840
Peripheral - nRF52840
Bluetooth...
I want to add wdt function in ble_app_uart. Please tell me where should I feed the wdt.
in below main loop?
for (;;)
{
power_manage();
nrf_drv_wdt_channel_feed(m_channel_id...
I'm trying to decide the best way to be able to have sub millisecond time keeping, but keep the processor sleeping until it gets a hardware interrupt.
Basically I need...
Hello Nordics Developer
I'm from indonesia, i'm electronics designer, i have develop new products using BLE, first develop i'm using nrf51 series but And my boss ask is there...
I'm trying to conserve space in the advertising packet, and would like to free up the space used by the 128 bit (16 byte) service item list, as this takes a minimum of 18...
Hello all,
I am working on nrf51 series for mesh application so regarding Pre addressing of controller how will get to know the adresses of SOC's in mesh network?
can...
I am using the nRF51822 with the s130 softdevice, and I would like to control three RGB LED modules with three PWMs (R, G, and B). For various conditions, either one, two...
[CONDITION]
1. R1 = 1.5M, R2 = 430K
2. GAIN = 1/2
3. RESOLUTION = 10bits
4. Single End
[ISSUE DESCRIPTION]
1. If voltage is changed by 0.1V step (4.1V -> 4.0V), the...
Hello
I wanted to ask what is the correct way to use NRF_LOG_* functions along with printf (with RETARGET_ENABLED 1 ) and normal UART initialized with standard:
const...
