I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
Hi,
For a new design with nRF51822-QFA, planning to use Johanson Balun and Chip antenna as shown in attached diagram. Not using any tuning components between Balun and...
Hi,
I was wondering why DFU_IMAGE_MAX_SIZE_BANKED is calculated as
(((DFU_REGION_TOTAL_SIZE/2) - DFU_APP_DATA_RESERVED))
and not
((DFU_REGION_TOTAL_SIZE - DFU_APP_DATA_RESERVED...
Hi, I'm using ble_app_uart application from latest nRF52 SDK on IAR compiler 7.1 and PCA10040 board.
It loads and runs debug code, but it does not add breakpoints on any...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Heading ##Here my PCA1000 board is getting detected in nRFgo studio even i can program and debug it, But i cant see COM PORT.
Can anybody help me out in this...
When i...
Hi,
I'm trying out the nRF52832 with kit PCA10040 V 0.9.0. I have S132 softdevice installed and running the ble_app_pwr_profiling example from nRF5 SDK v11.0.0.
I'm...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I am trying to manage the bonds as follows. I've defined the max bonded masters as 4 on my slave. When this list gets full, I delete a random bonded master on the slave (not...
I'm trying to flash to a device with the GCC toolchain using "make -f Makefile flash_softdevice" and nrfjprog fails with the message "ERROR: There is no debugger connected...
Hi.
I've searched this forum and also the code for pin muxings. One of post here said that any gpio can be configured for any output. However how is this done in code?...
I have a peripheral device based on the nRF51822, s130 and SDK 11.0.0. It's designed to only ever have one central device to which it's bonded. Out of the box, without a bond...
Hello.
I have a question.
I want to use UART without flow control.
In this case, I don't know what to set rts_pin_no and cts_pin_no of app_uart_comm_params_t.
Please...
