Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
We have the following environment:
1) nRF54H20-DK v0.9.1 and our custom board
2) nRF Connect SDK v3.2.1
3) Our simple project for testing BLE
4) nRF Connect...
MCU:NRF54L15，NCS SDK V3.2.4，android 7.0, nrf connect 4.26.1, cannot connect stably.
about 40 seconeds, the connect will disconnect, the android 7.0 side:reason is 0x08,...
Something seems to have broken in my VSC and/or Nordic extensions. Intellisense seems to be working for code, but cannot resolve any of my custom kconfig options.
I use...
I would like to sample a digital IO input from two IO's into the processor internal memory incrementally per every rising or falling edge of each of the signals.
Is there...
Trying to do ADV_DIRECT_IND advertisement.
We are trying to do the following advertisements
// ADV_IND Scannable and Connectable
// ADV_DIRECT_IND - Connectable...
I recently purchased an nRF52832 (XL52832-D01) for a wearables power management project. To test the module I flashed the basic blinky (zephyr). I'm using a ST-Link V2 as...
Hi
Brand new nRF52840-DK (PCA10056 rev 3.0.3, serial 1050245467, sticker on PCB). Never worked.
J-Link OB firmware update fails every time with: "Sending firmware data...
Hello! I am having troubles with my custom board using BL5340 from Ezurio. I have tried to flash it via my nrf5340 Audio DK but realized it doesnt support external Flashing...
Hi,
I am trying to set up a secure boot chain on nRF54L15dk with NCS 3.2.3 and an upgradable bootloader .
My intended boot chain is:
B0 / NSIB
S0 / S1 for the second...
Hello,
I would like to implement Device Firmware Update (DFU) over NFC.
Is this supported, and is there any recommended way to implement it? Are there any examples, reference...
I have two nRF52840DK boards that I was working with recently.
PCA10056 3.0.2 2024.33
I flashed one board with a BLE peripheral device code from the nRF connect sample...
Hello,
I'm using dmic module for sampling audio data from microphone. Recently I updated NCS to 3.2.2 and I started observing the following log: "Failed to allocate buffer...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
