Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
i am aiming to design a simple data transfer network. i am using 2 DKs. the first one is the central which runs a modified version of MULtilink Central Example and the seond...
I have continued to build upon the Nordic sdk10:gzll_ack_payload example using gcc-4.9-2015q1 on Linux. The differences are:
added UART for debugging (running at 460800...
Hello Nordevzone, so far, to the best of my knowledge, you can send data using API call sd_ble_gatts_hvx() with "notification packet" (quotemarks due to my limited knowledge...
AS i am trying to utilize GCC for more than 32 KB code size,
i use Eclipse which provides more friendly interface.
However, i am still experiencing some setting issues....
Hi,
Details:
I am using nrf sdk 10.0.0 and s130 Softdevice.I am using nrfgo studio for flashing SD,Application Hex files.I am using this nrfgo studio for past three months...
Hi,
I'm developing nRF51 proximity based device using nRF51822 that acts as BLE peripheral. It advertises continuously using connectable indirect mode.
User has Android...
app: nrf tool uart on iphone 5s
sdk: v8.1.0
softdevice: s110
example: ble_app_uart.
i have modify it based on the answer :
link text
my advertsing init as...
The device I completed has similar RSSI values at approximately zero distance as my development kit; starting with default Tx of 0dBm from the nRF51822 I achieve approximately...
I am having an issue implementing a WS2812b driver for the nrf51422 using the 210 softdevice. We currently have ANT enabled with a tx master only channel setup. The WS2812b...
What I would like to do is run a basic SPI program that reads data from a register on a non Nordic transceiver chip. My nRF51 would have to act as the master because the transceiver...
Hi,
Which service should I use for temperature non-health related, like room temperature, for example? I have browsed trough the Gatt Specification>Services of the Bluetooth...
Hello,
I follow the tutorial devzone.nordicsemi.com/.../
And in the step of copy examples
I only got ble_app_uart_s130_pca10028
and no package of s110 was found
I'm...
Per my another question:
devzone.nordicsemi.com/.../
I have taken the kind advice of Bjørn Spockeli but to no avail.
I tried this solution to enter debug mode:
...
I want to use the sd_ble_gatts_hvx() to send the notification with a packet, and the length of packet is 12 bytes, but the return value is "0x000C". I tested the length and...
