Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
On June 25th I asked a private question regarding be able to use the S110 soft device with the nRF51422. The following is the response I got:
....
Yes you can use the...
I am unable to to send notification for a customized service. I am testing a customized services that simply increments a variable every 3 seconds and sends notification with...
Hi guys,
I am trying to use the timer 1 on the nrf51822. I found the sample code online which could probably do the job for me. But I wanted to know what is the standard...
Hey Guys,
i asked this question already few days ago, but today i produced a log-file.
The procedure was:
Setup: SDKv6.0, SoftDevice v7.0.0, nrf51822
empty board...
Hi guys,
I had look at the ble_connectivity example in \nrf51822\Board\nrf6310\s110\ble_connectivity floader,but I can't found any documentation about this project.Is it...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
We found that in some cases. e.g. we started a background ble service. The ancs characteristics will change as the picture below. Do you think it's normal? Does the Nordic...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi guys,
i'm just porting my app from SDK5.2+SDv6.0.0 to SDK6.0+SDv7.0.0 and stuck with the device manager. There rises some questions, and i hope someone can help me....
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Hello,
About TWI in "nRF51_Reference_manual_v1.1.pdf",there is a register called "SHORTS".
I have a few question about this register:
Can I use SHORTS register to...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...