I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
After the latest update, the below setting allowing me to select nrfjprog as my device provider is now gone:
I am using the nRF Playground Docker container...
Hi,
I have been using NUS code to stream data between mobile and nrf5340 audio dk. is it possible to stream 256KB of data at a go? what is the maximum MTU size that i can...
I am using nrf connect sdk 2.7.0 with nrf52811.
My application is based on nrf5-sdk V 17.1.0 but now i want to port it to nrf-conneck sdk 2.7.0.
I want to know whether...
I have a problem with the package with nrf5 sdk, there for pca10100 examples are not there. i am trying to interface quadrature decoder with one encoder and it is not able...
Hello,I have a custom board using a Nordic nrf52823 microcontroller on it. I am using VSCode with the nrf connect SDK and the Zpehry RTOS- I want to make use Zephyr RTC to...
Is there any relevant assessment or introduction document of IC FMEA?
For example, the impact of abnormal short circuit and ordinary short circuit on chip 52832;
And...
1、I used the spi_bitbang routine to port it to the network core to run, and after the program was burned, I used an oscilloscope to measure the CLK pin waveform and there...
Hi,i I am testing the sample(ncs\v2.7.0\zephyr\samples\drivers\spi_bitbang) at a 52840DK board, with overlay setup like these:
spibb0: spibb0 {
compatible = "zephyr...
Hi nRF support team,
I am trying to add a new Custom Service and Characteristic an application on nRF82540 development kit using the nRF Connect SDK.
Can you please let...
Hello.
1. The nPM1300 PS v1.1 states in Section 6.1.1 the fllowing: "The default current limit is IBUS100MA (100 mA)". But the values after reset in registers VBUSINILIMSTARTUP...
I have finally got FOTA working with external flash, but I have a strange problem.
When the FOTA is complete, the mcuboot fails, but the new image boots correctly.
So...
Hi, I am trying to change the USB CDC/ACM com port name. I have read through some posts but they are very short or unanswered. It seems we can change the .inf driver file...
Hello everyone. I work with nrf52840 chip and previously I had an app with softdevice (s140) and use BLE bootloader. Everything works as expected. Next I want to use another...
We are using ncs 2.6.0 and nrf5340 audio dks.
Sample is nrf5340_audio broadcaster.
One dk is configured to work as Audio Broadcast BIS Source and other as Sink. By default...
