Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using nRFConnect 2.6.1 SDK on a nRF52833 with the speed build optimization.
I got two peripherals on the same SPI which is SPIM3. It is configured at 32MHz and...
Hello everyone,
I'm working on a Bluetooth device using the Zephyr framework. I need to maintain a current connection while also continuing to advertise. If another device...
I am using nrf5 sdk 17.1.0, segger embedded studio v6.40 and nrf52832-dk, when running the spi example, i do able to see the log only after the build, and when i reset the...
Hi,
I'm starting some development with NCS on the thread CLI sample and I wanted to adapt the code to work on a custom module. The goal is to be able to log some data through...
Hi,
I have been running thingy91 to learn more about nRF_Connect SDK and the assets tracker project.
I did all the beginner-level steps, hardware setup, nRF cloud setup...
Dear Nordic developer community,
I am in the process of developing a communication with the PC via the USB CDC ACM interface of the nRF52840 chip. The information received...
Hello Community! I am working on a small project on nrf52832_mdk beacon Where my main goal is to optimize the current consumption. I removed all the unused peripheral and...
Developing a device based on the nrf5340/nrf7002 pair, with a user interface.
I decided to use the Nordic 'buttons' and 'click-buttons' modules from the CAF framework for...
Hi All,
We are currently using this nRF-5340DK to understand the individual driver functionalities before we start our project with our kit .While doing so we encountered...
I am trying to get a pancake motor working with a nRF5340 using Zephyr in VSC. I have an intermediary board.
I keep getting this error:
I have these settings in the...
HI there, In the Serial LTE Modem documentation for the nRF9160 DK, it is mentioned that the GPIO voltage level should be 3V using SW9 when using an external MCU & UART2....
Hi, I am using the Nordic NRF52832 with SDK 16.
My device is configured to advertise continuously for a specific duration.
However, when tested using the nRF Connect app...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v1.6.0, but all attempts at device_get_binding("BMI270"), device_get_binding(DT_LABEL...
We are trying to interface Texas Instruments TMP144 using the UART in nrf52DK. We attach the sensor board to UART pins in nrf52DK put it seems that the transmitted data is...
Hi Mate,
Like most of the other tickets in this thread, I have a large application and need to DFU it using Bluetooth. I know nrf connect is not compatible with the single...
