Hi folks,
I'm having some UART trouble - help would be much appreciated, and thank you in advance.
------------------------
Overview:
I'm working on a project that...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
In the past few months I got aware, that some, in my opinion simple questions, get marked with
"This comment is under review"
and then nothing happens. For weeks, even...
running Windows 10 Pro 22H2 and using j-link v9
i tried to read firmware from nrf51822-QFAB by using " nrfjprog --readcode dump_nRF51822.hex", but it gave me an error...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello I want to add an extra config file based on the option in prj.conf or in Kconfg. For example: CONFIG_WIFI_SCAN_ONLY=y include the overlay-nrf7000-wifi-scan-only.conf...
Hello.
There was a problem with high current consumption when using Antenna 2 in some products.
The failure rate seems to be less than 7%, and the current consumption...
Hello,
I want to combine BLE, ANT+ and Apple Find My in one project.
I have permission to use ANT+ and Apple Find My.
I ran the two examples separately and they worked...
I have noticed that the RESETREAS register does not accumulate flags even though the documentation says it should. " Unless cleared, the RESETREAS register will be cumulative...
I have recently purchased a nrf7002 EK from element14.
I have connected it to nrf5340DK board and tried flashing the Wifi-shell sample application(with the help of video...
I’m not sure if I’m posting in the right forum, but since the EVK-ANNA-B402 uses the nRF52833, I thought this might be the place for questions related to it.
Steps followed...
I am using the cdc_acm example and have added a command to set and read tx power. I am trying to use the following commands for this.
BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL...
Hi,
while using the SoftDevice with MPSL on NCS/Zephyr (nRF52840), there will be a HardFault triggered without using Monitor Mode when a breakpoint is hit.
I understand...
Hi Nordic,
I have installed nRF Connect for desktop for using with nRF5340 Board . After completing the installation I'm getting the following Error.
I have reinstalled...
Features
nRF52840
nRF52832
System current consumption DC/DC at 3 V
0.5μA at 3V System OFF mode,
no RAM retention
1.5μA System ON mode, no RAM retention...
Hi
I'm running the blinky sample (modified) on a custom board based on nrf9160. When compiling with SDK2.3 and toolchain 2.3 the current consumption is about 84uA (LED off...
Hi,
I use VS code (windows 10) to program nRF9160DK under modem mfw_nrf9160_1.3.6, application Asset Tracker V2, JITP certificate generated by nRF Cloud and good SIM card...
What is the power consumption to check battery level?
How quickly at boot time is an accurate battery state of charge available?
What is the RDSon in the path from VBUS...
I am a long time user of Doxygen and I am familiar with its format. I have been using Doxygen manually in my nRF9160 code and it is working fine. I am using DoxyWizard to...
Hi,
I need to read the registers of the KTD2026 IC as specified in the datasheet.
In short I have to send a read command with the device address (0x30), the address...
