Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
Hello,
The documentation for the nRF5340 says that the UICR OTP registers can only be written to a non-0xFFFF value a single time: > Can only be written to a non 0xFFFF...
HI,
In our application, there is strange dependency for BLE service. The device is getting detected on ble scan only if we flash the ble application after flashing an application...
Hello,
with iOS 16 the connection during the update of the Firmware with IOS-DFU-Library not working. It is stop after few second with the error 202.
Do you know any solutions...
Hi, I restart advertising with ble_advertising_start and sd_ble_gap_adv_stop because I need to change the advertising interval in different situations. I am observing high...
I use nRF Connect for Desktop v3.12.0 (the latest) and its apps:
Bluetooth Low Energy (the latest standalone application v4.0.0)
Programmer v3.0.4 (the latest)
Can...
Is there support now for coded phy on nrf ble sniffer?
I'm using the nrf52840 devkit (hardware version 2.0.2 which supports coded phy) and sniffer works fine without coded...
It looks like the BT Mech spec has not been updated since 2017. Is there an update in progress and is Instaburst (or similar function) a candidate feature?
This would seem...
Hi,
I am facing a peculiar problem, wherein my application has two threads as in below:
Thread-1: is a preemptive thread which has UART functionality, along with UART...
I'm trying to run uart secured bootloader example in folder: @NRF5_SDK\examples\dfu\secure_bootloader\pca10040_uart_debug
but it doesn't work.
My setting is:
base...
Hi all!
I have created a simple application that only turns on a led and power it off using BLE in NRF52810. The thing is that simple app uses a huge RAM (~85%) and flash...
Hello,
I turned on the flash protect function through the CONFIG_FPROTECT switch, and the system kept running until spm_config_flash restarted.
Flash protect code in...
Dears,
Our custom board using nRF52833 cannot connect to Jlink after flashed a program.
I had the board connected with the Jlink via VCC, GND, SWDCLK, SWDIO and RESET...
Hi All,
I have a system with an nRF52840-dongle (PCA10059) acting as a serial port in windows 10. It runs extremely slowly. Sending 8kB over the interface takes 3 minutes...
I have the launch.json as shown below so that I can attach the debugger to a running image. This works with Cortex Debug. However, when using nRF Debug it does not seem to...
