I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I've been struggling with this for quite a while now. I've got a PCA10040 to spare that I am trying to use with nrf sniffer in Wireshark. I'm using a new iMac with the latest...
I have a problem I'm using nrf52840 DK. The task i want perform is start from idle state, wait for a button signal and the go out from idle, start with a loop where the code...
Hello ?
I was surprised that the program was organically well organized.
Based on the given installation manual, I completed the installation and corrected the program...
Hi!
We are using NRF52832 and NRF52840 with custom rf protocol.
I didn't found any information about time for applying new TXPOWER value of radio module.
Can I start...
Based on mesh sdk 3.1, open NRF_LOG_ENABLED in the light_switch_server example, ie NRF_LOG_ENABLED 1, the following error occurred during compilation: Linking light_switch_server_nrf52840_xxAA_s140_6...
I had two nRF52832 where one broadcasts with encrypted data of advertising beacon info and another nRF52832 should only scan without connecting and should decrypt the data...
Hello,
We are using nRF52832xx_aa controller for our product, the sleep current consumption is approx 2 uA @25 degree Celsius which is fine with me. But when the temperature...
We are writing SPI drivers for RF chip and blocked on the below issue. The issue we are facing is the Chip Select line is not active(active low) until the TX transaction is...
SDK: 12.3.0
SOFTDEVICE: s130_nrf51_2.0.1_softdevice
CHIP: nrf51822 AC 256K flash 32K ram
GCC flags:
# C flags common to all targets
CFLAGS += -DBOARD_CUSTOM
CFLAGS...
Hi,
I want to write or change the code in to nRF52832
I have some code this code i should write for nRF52832
kindly give any suggestion
here is the my code
uint8_t...
Hi everyone ,
I have a custom PCB using nrf52840 and i measured the current consumption using PPK(power profiler kit) . The sleep current value that it show is 4.5mA.
...
Hello,
I want that two devices can connect with each other and only each other . To do this i wanted to use whitelist on peripheral side but i found that i could use filtering...
Hello.
I'm using nRF SDK 15.2 together with the Nordic 802.15.4 driver ( here ).
When trying to add the libuarte module to my project I started having mysterious issues...
