I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I used nrf52832 sdk14.2 development, modified on the basis of the ble_app_template project, and ported some of the user code previously in sdk12.3 to sdk14.2. After I open...
Hi,
I want to store some data into flash and need to read before calling gap_params_init() in proxy_server demo.
1) when I am initializing flash manager using flash_manager_init...
Hi I wanted to flash a firmware in a Thingy52, I used Segger embedded studio and NRF52 DK to do that. I used the right cable but after flashing my Thingy52, it doesn't blink...
Hello dev zone !
I shall design a compact hardware solution wich is cost sensitive.
I need to use a NRF52832QFAA, I need to provide a 16mhz clock to a hardware peripheral...
I want to implement the function of long Attribute Value reading and writing in BLEV4.0. How should nrf52832 sdk14.2 implement this function? Is there a routine for reference...
I am trying to create a beacon application based on nrf52810.
I am using the following…
* SDK: 15.2.0
* IDE: Segger Embedded Studio
* Hardware: PCA10040 V1.1.1
...
hi.... i am working on ble_uart in segger ... while i am debugging my program stop at nrf_breakpoint_cond ...
how to enable the logging ... please have a look at pic......
hi...
i merged the ble_uart and twi sensor program in segger 15.2 using nrf52832
i have flashed the program successfully, i am getting fatal error while i am debugging...
Hi Sir
We'd want to make lot of nrf52840 devices, and all devices included open bootloader program,
however, the each device USB SDFU port number are different (COM30...
Hi,
I am usig nRF5_SDK_15.0.0_a53641 and writing a program with keil .
I am tryng to read data from the acceleration sensor( LSM303DLHC ) bu communication with BLENanov2...
Hello All,
Confirm the chip set replacement for the NRF51822 with NRF51802?
Can anyone suggest me which one is better with reference technical features.
Thanks
I used nrf52832 sdk14.2 development, modified on the basis of the ble_app_template project, and ported some of the user code previously in sdk12.3 to sdk14.2. After I open...
Hi
Over the last years working with Nordic I struggled from time to time over the disconnect reason 0x3E (BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED) on our devices with Central...
hii...
i have programmed the ble_uart with twi sensor ...
complied very successfully
but while i am debugging i am getting error in void twi_init()
why and also fatal...
