Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi. I want to output numbers to tm1637 display with nrf52832. The existing library is dedicated to Arudino, so we will contact you to change it for nRF52. (Existing library...
Hi,
I am having some task which for which i am using GPIOTE, PPI & TIMERS together to achieve and in SDK 14.2, the over all power consumption of my board is 10u which...
I am trying to integrate DFU into ble_app_uart example.
I am using nrf51422 board, sdk v10.0.0, soft device "s110_nrf51_8.0.0_softdevice.hex".
I have made some changes...
I'm trying to use Pin 0.21 as SCLK in the SDK15.2/examples/peripheral/spi/pca10056/blank/ses.
The example works fine with CLK on pin 3 (default) and on pin 29 (just tried...
Hi,
I created nrf52 project on Segger studio. I'm writing directly registers.(not SDK)
It includes i2c,uart and adc, this part is working now.
I want to add SoftDevice...
Hi,
I'm using Keil development tool.
The original bootloader start address is 0xE6000 and new bootloader start address is 0xE5000.
When I update to new bootloader, it...
hi...
What are the things I can check if I can't find my nRF51 upon scanning for BT devices? I am using nrf52832 and can successfully program the device via a Segger J-Link...
Simple and perhaps stupid, but important for me: the reports of detected devices I see in nRFConnect (desktop or mobile version) are based ONLY on BLE advertising packets...
Hi,
I am experiencing problems with the app_error_handler function defined in app_error_handler_iar_c provided with the SDK V15.0.0.
If the function gets called when debugging...
HI team,
I am a beginner of Nordic nrf52840 DK, I would like to control the AC ceiling fan using the nrf52840 board with pwm library. As, I can see we can use either single...
errr_code=sd_ble_uuid_encode(p_target_uuid,&raw_uuid_len,raw_uuid);when i debug and going to find uuid my debugger will move to NVIC_systemReset.i am running uart central...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Hi,
I am currently trying send value to a write characteristic of the server of a custom central device with a nrf52832 peripheral device. I have been able to connect with...
Hi
I am going to use the ble_app_uart example , the sdk version is 15.2.0
I only modify the vendor specific UUID , and download in the NRF52840, it does not work, i can...
Hi there,
I am about to perform an RF emission test to my product which is using a nRF52 chip and different RF sources as wifi and cellular and I was requested to:
...